Results 101 to 110 of about 318,902 (287)
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Novel application of PEG/SDS interaction as a wettability modifier of hydrophobic carbonate surfaces
Petroleum Science, 2018 Wettability alteration of carbonate reservoirs from oil-wet to water-wet is an important method to increase the efficiency of oil recovery. Interaction between surfactants and polymers can enhance the effectiveness of surfactants in EOR applications.
Nasim Heydari +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses
Advanced Engineering Materials, EarlyView.Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk +4 more
wiley +1 more source
Evaluating Treatment Parameters Toward Optimizing Production From Gas Reservoirs Using Wettability Alteration [PDF]
, 2019 Retrograde condensation in gas reservoirs results in a significant loss in well deliverability. A ring of condensate forms near the wellbore as a result of reservoir pressure falling below the dew point of the reservoir gas.
Ajagbe, Oluwatobi
core
Brine Divalent Ions Impacts on Wettability Alteration of Carbonate Rock Sample at Presence of DTAB
, 2017 Among many Enhanced Oil Recovery (EOR) methods, chemical flooding for wettability alteration of carbonate oil-wet rock is one of the most noticeable methods amid researchers.
S.N. Hosseini +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan +4 more
wiley +1 more source
An experimental study of the effects of bacteria on asphaltene adsorption and wettability alteration of dolomite and quartz. [PDF]
Sci Rep, 2023 Soleimani Y +4 more
europepmc +1 more source