Results 141 to 150 of about 13,201 (296)
Wetting-drying effect on the strength and microstructure of cement-phosphogypsum stabilized soils
Phosphogypsum has often been used as an effective and environmentally friendly binder for partial replacement of cement, improving the engineering properties of slurries with high water content.
Lingling Zeng +3 more
doaj +1 more source
Advances in Sustainable and Wearable Textile Based Soft Robotics
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas +6 more
wiley +1 more source
Conformal Metallosaccharide Hybrid Films for Protecting Wood Surfaces From Environmental Damage
Ti‐ribose hybrid films fabricated by molecular layer deposition form a conformal and uniform coating on wood surfaces, which provides water repellence, dimensional stability, and resistance to acidic and alkaline environments, while preserving the natural appearance.
Wenwen Wang +7 more
wiley +1 more source
Hierarchical MXene‐Derived NTP/C Nanohybrids for Cryogenic Sodium‐Ion Batteries
A hierarchical MXene‐derived NaTi2(PO4)3/C nanohybrid enables efficient sodium‐ion storage down to −40°C by integrating fast ion–electron transport pathways with an ether‐based electrolyte. The system promotes dominant pseudocapacitive behavior and forms a robust inorganic‐rich SEI, collectively mitigating kinetic and interfacial limitations, thereby ...
M. Sai Bhargava Reddy +5 more
wiley +1 more source
Co‐delivery of electrosprayed EDOT and oxidant enables bulk oxidative polymerization during layer‐by‐layer fabrication, creating stable, highly conductive 3D PEDOT structures. This Atomized Oxidative Polymerization (AOP) overcomes the surface deposition‐only and matrix‐limited conductivity of conventional Vapor Phase Polymerization (VPP) and PEDOT:PSS ...
Tazdik Patwary Plateau +2 more
wiley +1 more source
Top‐down organic pillaring expands the interlayer spacing of bulk‐sized MoS2 particles while preserving the bulk morphology. Operando X‐ray diffraction and electrochemical dilatometry show that MoS2‐bulk undergoes solvent co‐intercalation in diglyme electrolyte, causing large structural expansion, while pillared, expanded MoS2 suppresses solvent uptake
Jaehoon Choi +8 more
wiley +1 more source
Highly hydrophilic surfaces (water contact angle, ≈17.7°) exhibiting surprising water slipping performance (sliding angle, ≈7.3°) are successfully prepared via simple chemisorption of polyethylene glycol (PEG) organosilane and subsequent alkali‐treatment.
Hyeonjin Kim +5 more
wiley +1 more source
Among the slope hazards caused by rainfall, not all of them occur directly during storm washout, and the wetting–drying cycles’ effect on the rainfall–evaporation process is an important cause of shallow slope instability. In this study, taking the slope
Van Son Bang +8 more
doaj +1 more source
Wood Cellulosic Membrane With Abundant Nanochannels for Stabilizing Aqueous Zn‐Ion Batteries
A wood‐derived cellulosic membrane separator is developed to suppress dendrite growth in aqueous zinc‐ion batteries. Its aligned nanochannels and hydroxyl‐rich surfaces enable uniform Zn2+ flux, water immobilization, and interfacial stabilization. Zn||Zn cells achieve 1920 h of cycling, Zn||Cu cells maintain 99.5% Coulombic efficiency over 1000 cycles,
Song Wei +8 more
wiley +1 more source
Coagulative granular hydrogels are composed of packed thrombin‐functionalized microgels that catalyze the conversion of fibrinogen into a secondary fibrin network, filling the interstitial voids. This bio‐inspired approach stabilizes the biomaterial to match the robustness of bulk hydrogels without compromising injectability, mimicking the initial ...
Zhipeng Deng +16 more
wiley +1 more source

