Results 81 to 90 of about 46,332 (305)
Shear Strength Durability Investigation for Gypseous Soil Enhanced by Pectin Biopolymer
Tikrit Journal of Engineering SciencesSeveral studies have shown that biopolymers improve soil; however, they mostly looked at how the shear strength and collapsibility improved without looking at how long the treatments would last.
Farouk M. Muhauwiss +2 more
doaj +1 more source
Modelling the thermo-mechanical volume change behaviour of compacted expansive clays [PDF]
, 2009 Compacted expansive clays are often considered as a possible buffer material in high-level deep radioactive waste disposals. After the installation of waste canisters, the engineered clay barriers are subjected to thermo-hydro-mechanical actions in the ...
Cui, Yu-Jun, Tang, Anh-Minh
core +5 more sources
Advanced Engineering Materials, EarlyView.This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar +7 more
wiley +1 more source
Benefits of greenhouse gas mitigation on the supply, management, and use of water resources in the United States [PDF]
, 2014 Climate change impacts on water resources in the United States are likely to be far-reaching and substantial because the water is integral to climate, and the water sector spans many parts of the economy.
Boehlert, B +13 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Yantu gongcheng xuebaoThe Long-term wetting-drying cycles can weaken the engineering characteristics of subgrade fillers, resulting in engineering disasters. It is necessary to study the effects of the wetting-drying cycles on their microstructure and water-retention ...
YANG Xu 1, CAI Guoqing 1, 2, LIU Qianqian 1, LI Fengzeng 3, SHAN Yepeng 1
doaj +1 more source
Advances in Civil Engineering, 2018 This study focused on the swelling behavior of swelling rock from canal basement under multiple drying-wetting (D-W) cycles. A series of laboratory tests were conducted on a swelling rock, with the cracking and strength behaviors investigated.
Chen Zhang +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan +8 more
wiley +1 more source
Formulation of itraconazole nanococrystals and evaluation of their bioavailability in dogs [PDF]
, 2014 The aim of the study is to increase the bioavailability of itraconazole (ITRA) using nanosized cocrystals prepared via wet milling of ITRA in combination with dicarboxylic acids.
Adriaensens, Peter +7 more
core +1 more source