Results 71 to 80 of about 212,914 (312)
Asymmetric Contact Engineering for Bottleneck‐Free Transport in 2D MoS2 Field‐Effect Transistor
Advanced Functional Materials, EarlyView.Performance of 2D semiconductor transistors is limited by carrier transport bottlenecks arising from specific device geometries. By identifying this structural limitation, a bottleneck‐free asymmetric transistor architecture (BATA) is introduced to improve carrier transport.
Jinhyeok Pyo +10 more
wiley +1 more source
Conductance‐Dependent Photoresponse in a Dynamic SrTiO3 Memristor for Biorealistic Computing
Advanced Functional Materials, EarlyView.A nanoscale SrTiO3 memristor is shown to exhibit dynamic synaptic behavior through the interaction of local electrical and global optical signals. Its photoresponse depends quantitatively on the conductance state, which evolves and decays over tunable timescales, enabling ultralow‐power, biorealistic learning mechanisms for advanced in‐memory and ...
Christoph Weilenmann +8 more
wiley +1 more source
Advanced Functional Materials, EarlyView.ABSTRACT Metal oxide (MOx)‐based NO2 gas sensors typically require high temperatures or ultraviolet light, limiting their practical use. To enable visible‐light activation at room temperature, efficient and stable photosensitizers should be integrated with nanostructured MOx hosts.
Yeonji Yuk +10 more
wiley +1 more source
BuildingsAs a weak part of the concrete tower in wind turbines, the insufficient shear capacity of vertical joints can cause the local shear failure of the tower, reduce the overall bearing capacity and stability of the tower, and lead to safety issues.
Yang Zhou +5 more
doaj +1 more source
Study of the integration of wind tunnel and computational methods for aerodynamic configurations [PDF]
A study was conducted to determine the effectiveness of using a low-order panel code to estimate wind tunnel wall corrections. The corrections were found by two computations.
Ashby, Dale L., Browne, Lindsey E.
core +1 more source
Jet engine powers large, high-temperature wind tunnel [PDF]
, 1967 Wind tunnel for large component testing uses a jet engine with afterburner to provide high temperatures /1200 degrees to 2000 degrees F/ and controlled high velocity gas.
Benham, T. F., Mulliken, S. R.
core +1 more source
Advanced Functional Materials, EarlyView.In this report, we demonstrate that a crystalline phase of 52nm thick NiFe2O4 can be grown by RF sputtering on top of γ‐Al2O3(8nm)/SrTiO3 at a significantly low temperature (150 °C) without compromising the mobility and carrier density of the 2D electron gas at the γ‐Al2O3(8nm)/SrTiO3 interface.
Amit Chanda +11 more
wiley +1 more source
CFD and experimental data of closed-loop wind tunnel flow
Data in Brief, 2016 The data presented in this article were the basis for the study reported in the research articles entitled ‘A validated design methodology for a closed loop subsonic wind tunnel’ (Calautit et al., 2014) [1], which presented a systematic investigation ...
John Kaiser Calautit, Ben Richard Hughes
doaj +1 more source
Advanced Functional Materials, EarlyView.In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa +19 more
wiley +1 more source
Materials and construction techniques for cryogenic wind tunnel facilities for instruction/research use [PDF]
The results of the cryogenic wind tunnel program conducted at NASA Langley Research Center are presented to provide a starting point for the design of an instructional/research wind tunnel facility.
Morse, S. F., Roper, A. T.
core +1 more source