Results 41 to 50 of about 346,306 (411)
CFD and experimental data of closed-loop wind tunnel flow
Data in Brief, 2016 The data presented in this article were the basis for the study reported in the research articles entitled ‘A validated design methodology for a closed loop subsonic wind tunnel’ (Calautit et al., 2014) [1], which presented a systematic investigation ...
John Kaiser Calautit, Ben Richard Hughes
doaj +1 more source
Wind Tunnel Testing of Passive High-Lift Systems [PDF]
INCAS Bulletin, 2012 This paper presents experimental results obtained with passive high lift systems using a combination of smart flap kinematics and vortex generators. A mid-scale 2.5D wind tunnel model based on DLR-F15 is tested in INCAS Subsonic Wind Tunnel, swept at 30 ...
Andreea BOBONEA +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi +3 more
wiley +1 more source
Selection criteria of optimal conditions for supersonic tests in a blowdown wind tunnel [PDF]
Scientific Technical Review, 2016 A natural desire of a wind tunnel test engineer is to plan and perform a test that will resemble the actual flight conditions as closely as possible. Geometric similarity and identical flight and wind tunnel Mach numbers are the primary requirements and ...
Damljanović Dijana, Vuković Đorđe
doaj
Airloads Correlation of the UH-60A Rotor inside the 40- by 80-Foot Wind Tunnel
International Journal of Aerospace Engineering, 2014 The presented research validates the capability of a loosely coupled computational fluid dynamics (CFD) and comprehensive rotorcraft analysis (CRA) code to calculate the flowfield around a rotor and test stand mounted inside a wind tunnel.
I-Chung Chang +2 more
doaj +1 more source
Blockage Effects in Wind Tunnel Tests for Tall Buildings with Surrounding Buildings
Applied Sciences, 2022 To study the blockage effects in wind tunnel tests for tall buildings with surrounding buildings and establish a reasonable calculation method for the blockage ratio, this paper carried out fifty-one test conditions of pressure model wind tunnel tests ...
Lei Wang +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A lack of standard approaches for testing and reporting the performance of metal halide perovskites and organic semiconductor radiation detectors has resulted in inconsistent interpretation of performance parameters, impeding progress in the field. This Perspective recommends key metrics and experimental details, which are suggested for reporting in ...
Jessie A. Posar +8 more
wiley +1 more source
Journal of the Visualization Society of Japan, 1995 Wind tunnel testing in general is described for those who are not familiar with this field of engineering. Wind tunnels are grouped according to the testing speeds, test section geometry and configurations, and tunnel circuit shapes. Similality laws of and problems in wind tunnel testings are presented.
openaire +2 more sources
Advanced Functional Materials, EarlyView.Novel ferrocene derivatives (e.g., FcPhc2) are used as an ultrathin layer hole‐blocking layer, reducing hole injection from the Ag contact. This results in an ultralow noise spectral density of 1.2 × 10−14 A Hz−1/2, and a high specific detectivity of 8.1 × 1012 Jones at −0.5 V.
Eunyoung Hong +16 more
wiley +1 more source