Results 141 to 150 of about 6,096 (195)

A Review of Mechanical Reinforcement and Piezoresistive Self‐Sensing in Carbon Nanotube Fiber Composites

Polymer Composites, EarlyView.
PSPP‐TRL mapping of CNT‐modified CFRP literature, with four recurring confusions resolved and five scale‐up problems quantified. ABSTRACT Carbon nanotube‐modified fiber composites are often presented as a route to stronger, tougher, and self‐sensing structural materials.
Sanan H. Khan
wiley   +1 more source

Advances, Challenges, and Recommendations for Non-Destructive Testing Technologies for Wind Turbine Blade Damage: A Review of the Literature from the Past Decade. [PDF]

Sensors (Basel)
Qin G, Jin Y, Qiao L, Wu Z.
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Mechanical Behavior and Damage Mode Identification of Wind Turbine Blade GFRP Shear Webs Based on Acoustic Emission Detection Technology. [PDF]

Sensors (Basel)
Xu L, Zheng J, Wang W, Li Z, Zou H.
europepmc   +1 more source

Fusion Bonding Repair of Impact‐Damaged Elium Laminates: Comparison of Hot Pressing and Joule Heating

Polymer Composites, EarlyView.
Joule Heating‐Enabled Repair of Impact‐Damaged GFRP/Elium Laminates. ABSTRACT This study investigates the repairability of glass fiber‐reinforced Elium (GFRP/Elium) laminates incorporating nickel‐coated carbon veils, focusing on hot pressing and Joule heating as fusion bonding repair techniques.
Ozan Can Zehni
wiley   +1 more source

Mechanical Properties and Feasibility of GFRP from Decommissioned Large-Scale Wind Turbine Blades for Wave Energy Converter: A Case Study. [PDF]

Polymers (Basel)
Li YW, Lai JS, Zhou BZ, Cheng L.
europepmc   +1 more source

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

Journal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu, Harrison Hayworth, Shiren Wang   +2 more
wiley   +1 more source

Aerodynamic performance optimization of the archimedes spiral wind turbine: combined experimental and CFD analysis of step ratio and blade number effects. [PDF]

Sci Rep
Faisal AE, Lim CW, Al-Quraishi BAJ, Milano J, Tan CH, Chen CP.   +5 more
europepmc   +1 more source

Multimodal dataset for wind turbine blade monitoring during lightning strikes. [PDF]

Sci Data
Li T, Li C, Qin Y, Tan L, Jiang B, Deng H.   +5 more
europepmc   +1 more source

Multi-parameter pendulum tuned particle damper for vibration suppression in offshore wind turbine towers. [PDF]

Sci Rep
Xiao W, Xie Z, Yao W, Mo F, Cai Z.
europepmc   +1 more source