Results 181 to 190 of about 15,562 (264)

Algorithm for detecting surface defects in wind turbines based on a lightweight YOLO model. [PDF]

Sci Rep
Wu Z, Zhang Y, Wang X, Li H, Sun Y, Wang G.   +5 more
europepmc   +1 more source

From Wind Turbine Blades to Recycled Glass Fibers: Analytical Modeling and Lab‐Scale Recycling Protocol

Polymer Composites, EarlyView.
Lab‐Scale Composite Dissolution Experiments were used for Prediction of Dissolution Duration. ABSTRACT Glass fiber‐reinforced thermosets are widely used in wind turbine blades. However, recycling these materials remains challenging because thermoset matrices cannot be remelted, and high‐temperature processes degrade glass fibers.
Agathe Navailles, Justine Beauson, Robert Pierce, Tom Andersen Løgstrup, Rajnish Kumar, Yi Chen, Stergios Goutianos   +6 more
wiley   +1 more source

Materials Design and Structural Health Monitoring of Horizontal Axis Offshore Wind Turbines: A State-of-the-Art Review. [PDF]

Materials (Basel)
Tong Y, Liu W, Liu X, Wang P, Sheng Z, Li S, Zhang H, Meng Y, Zhu Y, Lei X, Lin YT, Jiao P.   +11 more
europepmc   +1 more source

Potential of Thermoset Polyolefins for FRP Concrete Reinforcing Bars

Polymer Composites, EarlyView.
Overview of XLPO and pDCPD resins for FRP reinforcing bars, highlighting resin chemistry, key performance characteristics, fiber sizing interactions, and principal degradation mechanisms in concrete environments. ABSTRACT Although thermoset polyolefins offer resistance to hydrolytic degradation and favorable processing characteristics, their potential ...
Osama Omar, Farzaneh Mahmoudi, Leonidas G. Bachas, Francisco De Caso, Brahim Benmokrane, Antonio Nanni   +5 more
wiley   +1 more source

Elevation data are insufficient for assessing viewshed externalities of wind turbines. [PDF]

Proc Natl Acad Sci U S A
Lang C, Dong L, Peach M.
europepmc   +1 more source

Mechanical and Impact Response of Adhesively Bonded ASA/PA12 Sandwich Structures Produced by Fused Filament Fabrication

Polymer Engineering &Science, EarlyView.
Adhesively bonded ASA/PA12 FFF sandwich structures reveal that interfacial compliance governs mechanical performance. Cyanoacrylate enhances strength but induces brittle failure, while polyurethane improves ductility and impact resistance, demonstrating that adhesive properties and stacking sequence are critical design parameters for optimizing multi ...
Berkay Ergene, Bayram Yildiz, Tolgahan Ermergen, Çağın Bolat   +3 more
wiley   +1 more source

A new approach for improving dynamic fault ride through capability of gridctied based wind turbines. [PDF]

Sci Rep
Dayo SA, Memon A, Memon ZA, Jumani TA, Abbas G, Othmen S, Yousef A, Wijaya AA.   +7 more
europepmc   +1 more source

Erosion Resistance Enhancement in Epoxy Composites by Recycled Rubber: Effect of Rubber Type

Polymer Engineering &Science, EarlyView.
Erosion resistance enhancement in epoxy composites by recycled rubber. ABSTRACT Epoxy‐based materials have low erosion resistance due to their brittle nature, and toughness modification stands out for enhancing it. At this stage, the use of waste rubber as a reinforcement component in the composite system is of interest due to its role in providing ...
Orkan Baran Korkusuz, Şehriban Öncel, Bağdagül Karaağaç, Tamer Sınmazçelik   +3 more
wiley   +1 more source

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

Journal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu, Harrison Hayworth, Shiren Wang   +2 more
wiley   +1 more source

A novel optimal design approach for bladeless wind turbines considering mechanical properties of composite materials used. [PDF]

Sci Rep
Mohamed Z, Soliman M, Feteha M, Saber E.
europepmc   +1 more source