Results 101 to 110 of about 4,056,813 (387)

Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer, Lukas Spano, Sebastian Pohl, Carolin Körner, Matthias Markl   +4 more
wiley   +1 more source

Evaluating semi-empirical wave forecasting method CEM in the Strait of Hormuz

International Journal of Coastal and Offshore Engineering, 2019
Wind waves are one of the most important phenomena that should be considered in coastal and offshore activities. They have many effects on coastal environments such as wave-induced erosion, sediment and pollution transport and even in the worst cases ...
Mahmud reza abbasi
doaj  

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Development of an optical imaging technique for particle number density

Journal of Fluid Science and Technology, 2018
Accurate measurements of particle number density along with particle diameters and velocities are strongly required both in academic and industrial fields.
Naohisa TAKAGAKI, Koji IWANO, Emil ILYASOV, Satoru KOMORI, Yoshiyuki SHIRAKAWA   +4 more
doaj   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Copper Nanocrystallization in Anodic Oxide Films of Ti–Cu‐Based Bulk Metallic Glass and Its Effect on the Corrosion Resistance and Cytocompatibility

Advanced Engineering Materials, EarlyView.
Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan, Nora Fernández Navas, Thorgund Nemec, Ivan Kaban, Ute Hempel, Andrea Voss, Volker Hoffmann, Darius Pohl, Annett Gebert   +8 more
wiley   +1 more source

Mass transfer velocity across the breaking air–water interface at extremely high wind speeds

Tellus: Series B, Chemical and Physical Meteorology, 2013
Mass transfer velocity kL across the wind-driven air–water interface was estimated at extremely high wind speeds (up to U10=70 m s−1) in a high-speed wind-wave tank by measuring changes in CO2 concentration in the water.
Koji Iwano, Naohisa Takagaki, Ryoichi Kurose, Satoru Komori   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Ocean Wind and Wave Measurements Using X-Band Marine Radar: A Comprehensive Review

Remote Sensing, 2017
Ocean wind and wave parameters can be measured by in-situ sensors such as anemometers and buoys. Since the 1980s, X-band marine radar has evolved as one of the remote sensing instruments for such purposes since its sea surface images contain considerable
Weimin Huang, Xinlong Liu, Eric W. Gill
doaj   +1 more source

WAVE HEIGHT DISTRIBUTION OF WIND WAVES OVER LONG WAVES

Coastal Engineering Proceedings, 1976
Influence of long wave on the wave height distribution of wind waves was studied through the laboratory experiment. Experiments were conducted in a wind-wave tank where the wind waves were generated by a wind blower and the long waves were developed by an oscillating pendulum type wave generator. The wave height distribution of the wind waves over long
Shan-Hwei Ou, Frederick L. W. Tang
openaire   +2 more sources