Results 261 to 270 of about 19,161 (304)

Study on the Fatigue Bending Strength of Cylindrical Components Manufactured by External WAAM. [PDF]

Materials (Basel)
Nguyen VM, Minh PS, Phan DTT, Toan HDS.
europepmc   +1 more source

Development of a Low-Cost Infrared Imaging System for Real-Time Analysis and Machine Learning-Based Monitoring of GMAW. [PDF]

Sensors (Basel)
Muñoz Chávez JJ, Lira MNS, Pizo GAI, Payão Filho JDC, Alfaro SCA, Motta JMSTD.   +5 more
europepmc   +1 more source

Physics-informed machine learning-based real-time long-horizon temperature fields prediction in metallic additive manufacturing. [PDF]

Commun Eng
Tian M, Mu H, Liu T, Li M, Ding D, Zhao J.   +5 more
europepmc   +1 more source

Cost-effective laser metal deposition of 304L stainless steel for repairing and enhancing 316L and mild steel engineering components. [PDF]

Sci Rep
Elgazzar H, Abdel-Sabour H, Abdel-Ghany K.   +2 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Forming Process of Wire and Arc Additive Manufacture

Materials Science Forum, 2021
The forming process of wire and arc additively manufacture (WAAM) was studied using the self-developed and designed WAAM system. The single-pass and single-layer weld bead samples were prepared with different process parameters, and the cross-sectional dimensions of the weld bead were measured.
Lei Zou, Lei Li, Jian Hua Cai, Hai Ying Yang, Jun Chen   +4 more
openaire   +1 more source

Ultracold-Wire and arc additive manufacturing (UC-WAAM)

Journal of Materials Processing Technology, 2021
Abstract This study presents a new variant of Wire and Arc Additive Manufacturing named Ultracold-Wire and Arc Additive Manufacturing (UC-WAAM), in which the electric arc is established between the wire feedstock material and a non-consumable tungsten electrode. A feasibility study was performed on HSLA steel. A comparison with conventional Gas Metal
Tiago A. Rodrigues, Valdemar R. Duarte, R.M. Miranda, Telmo G. Santos, J.P. Oliveira   +4 more
openaire   +1 more source

Machinability of wire and arc additive manufactured components

CIRP Journal of Manufacturing Science and Technology, 2021
Abstract Wire and Arc Additive Manufacturing (WAAM) aims to be a cost-effective and material-efficient process to produce medium and large-scale metal parts. Nevertheless, post-processing is still required due to the low quality of the as-deposited surface.
Nataliia Chernovol, Abhay Sharma, Tegoeh Tjahjowidodo, Bert Lauwers, Patrick Van Rymenant   +4 more
openaire   +1 more source

Material Properties for Wire‐and‐arc Additively Manufactured Steel

ce/papers, 2022
AbstractIn the era of internet and robots, sophisticated devices and real‐time simulation, the construction sector remains highly dependent on manual labor which is also the main source of delays, lack of quality, and human injuries. The rapid development in technological areas such as mechatronics, computers, sensors, programming, human interfaces ...
Trayana Tankova, Carlos Zhu, Ricardo Branco   +2 more
openaire   +1 more source

A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium

Materials Science and Technology, 2018
Although wire arc additive manufacturing (WAAM) has proven its capability of fulfilling demands of production of medium-to-large-scale components for automotive and allied sectors made up of aluminium, at present, WAAM cannot be applied as a fully fledged manufacturing process because of practical challenges such as under-matched mechanical properties,
openaire   +1 more source