Results 161 to 170 of about 644,787 (247)

Using a Zero‐Strain Reference Electrode to Distinguish Anode and Cathode Volume Changes in a Solid‐State Battery

Advanced Materials Interfaces, EarlyView.
Volume changes of a solid‐state battery cell are separated into the individual contributions of anode and cathode. Simultaneously determining the “reaction volumes” of both electrodes requires a reference electrode with a pressure‐independent potential.
Mervyn Soans, Benedikt Huber, Marcel Drüschler, Dominic Bresser, Alberto Varzi, Christoffer Karlsson   +5 more
wiley   +1 more source

Accessible Chemical Benchmarking of Nanoparticle Growth Using Oxidation-Reduction Potential Sensors. [PDF]

Chem Mater
Halford GC, Hertle S, Obedin KL, Sublett AM, Harmon KM, VanGelder LE, Personick ML.   +6 more
europepmc   +1 more source

Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization

Advanced Materials Interfaces, EarlyView.
Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan, Thomas D. Small, Gregory F. Metha, Mahmoud Adel Hamza, Thomas J. O'Dea, Yideng Shen, Cameron J. Shearer   +6 more
wiley   +1 more source

A Low-Cost, Lightweight High-Frequency Ultrasound Transducer with Aluminum Electrodes and 3D-Printed Polymer Housing. [PDF]

Biosensors (Basel)
Kim H, Jin W, Kim DK, Kim J, Park J.
europepmc   +1 more source

Defect‐Driven Charge Separation in Ba‐Doped SrTiO3: Correlating Photoelectrochemical Performance With Dye‐Selective Photocatalysis

Advanced Materials Interfaces, EarlyView.
Ba‐doped SrTiO3 perovskites establish a direct correlation between photoelectrochemical activity and photocatalytic performance. Optimized Ba0.5Sr0.5TiO3 exhibits enhanced charge separation, photocurrent generation, and visible‐light‐driven dye degradation through defect‐induced oxygen vacancies and lattice distortion.
Sagar A. Nikam, Somnath Ladhane, Vikas P. Mhaske, Gotan H. Jain, Sandesh R. Jadkar, Shashikant P. Patole, Ganesh E. Patil   +6 more
wiley   +1 more source

Soft Probe Electrical Contact: Eliminating Electrode Deposition and Enabling Reliable Measurements of Emerging Materials. [PDF]

Materials (Basel)
Yoshitake M, Kinoshita K, Matsuo H, Sakai S, Li S.   +4 more
europepmc   +1 more source

Molybdenum Disulfide Bilayers Hybridized With Reduced Graphene Oxide Nanosheets for Enhanced Hydrogen Evolution Reaction

Advanced Materials Interfaces, EarlyView.
The integration of reduced graphene oxide nanosheet‐hybridized molybdenum disulfide bilayers to enhance hydrogen evolution reaction capabilities unveils thrilling opportunities for strain engineering, defect manipulation, and sophisticated twist‐angle assemblies with 2D heterostructures.
Bruno Ferreira Brischi, Gabriela Frajtag, João Pedro da Silva Mariano, Laís Fernanda Medeiros Ruela, Gustavo Duarte Verçosa, Camila Desiderio Fernandes, Murilo Santhiago, Letícia Mariê Minatogau Ferro, Leandro Merces   +8 more
wiley   +1 more source

Textile‐Based Capacitive Pressure Sensors Enabled by Ultrasonic Spray‐Coated Carbon Black Electrodes and Electrostatic Flocking

Advanced Materials Interfaces, EarlyView.
A 4‐layer Kevlar‐based composite is fabricated by combining ultrasonic spraying and electrostatic flocking. Carbon black dispersion is first deposited onto Kevlar fabric to create a conductive electrode. Nylon fibers are then electrostatically flocked onto the coated fabric, forming a dielectric layer.
Mengdi Chen, Hongxuan Li, Lei Shi, Fei Huang, Yuting Zhu, Wee Chen Gan, Swee Tiam Tan, Kean Aw   +7 more
wiley   +1 more source

A Wearable Device to Measure Bioimpedance and Electrodermal Activity. [PDF]

Sensors (Basel)
de León JP, Beltrán JR, Asiain D.
europepmc   +1 more source

Thermoplastic Dielectric Coatings for Flexible Electrodynamic Dust Shields: Structural and Functional Performance

Advanced Materials Interfaces, EarlyView.
Thermoplastic attachment is introduced as a scalable surface coating strategy to improve the durability and dielectric reliability of flexible electrodynamic dust shields. By embedding chemically modified reduced graphene oxide (CMrGO) electrodes within thermoplastic laminates, mechanical degradation, abrasion damage, and vacuum‐induced electrical ...
Ide E. Onal, Emily A. Ryan, Luca Scifoni, Thomas M. Orlando, Álvaro Romero‐Calvo, Julie S. Linsey, Meisha L. Shofner   +6 more
wiley   +1 more source