Results 111 to 120 of about 941,826 (327)

Melting behavior of an organic phase change material in a square thermal energy storage capsule with an array of wire electrodes

Applied Thermal Engineering, 2023
R. Deepak Selvakumar, Jian Wu, Yulong Ding, Ahmed K. Alkaabi   +3 more
semanticscholar   +1 more source

Low Resistance Interphase Formation at the PEO‐LiTFSI|LGPS Interface in Lithium Solid‐State Batteries

Advanced Materials Interfaces, EarlyView.
Interfacial charge transfer and low‐resistance interphase formation between PEO‐based polymer and Li10GeP2S12 solid electrolytes are investigated using multi‐electrode impedance spectroscopy and advanced analytical techniques such as XPS and ToF‐SIMS.
Ujjawal Sigar, Timo Weintraut, Sebastian L. Benz, Semih Engün, Sascha Kremer, Anja Henss, Felix H. Richter   +6 more
wiley   +1 more source

Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization

Advanced Materials Interfaces, EarlyView.
Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan, Thomas D. Small, Gregory F. Metha, Mahmoud Adel Hamza, Thomas J. O'Dea, Yideng Shen, Cameron J. Shearer   +6 more
wiley   +1 more source

Thermal properties of melt polymers by the hot wire technique

Polymer Testing, 2005
Over recent years mathematical modelling has become an established tool for improving process control and product quality in polymer processing. As models become more sophisticated, there is an increasing need for reliable thermophysical properties data.
openaire   +1 more source

Conductive Additives for Next‐Generation Batteries: Emphasizing the Potential of Bio‐Derived 3D Carbon Architectures at Electrode–Electrolyte Interfaces

Advanced Materials Interfaces, EarlyView.
3D conductive frameworks can maintain continuous electron transport, mechanical stability, and interfacial integrity, helping next‐generation batteries operate more efficiently. This Review examines their relevance to Si anodes, all‐solid‐state batteries, and dry‐processed electrodes, and highlights bio‐derived carbons as sustainable, structurally ...
SeoYoung Ha, Inseo Ko, Jongyoung Choi, Weon Ho Shin, Sung Cik Mun, Jong Ho Won   +5 more
wiley   +1 more source

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

Features of electrode wire melting in surfacing by plasma-MIG process

, 2001
Определено влияние полоцилиндрической дуги при наплавке способом плазма-МИГ на характер плавления порошковой проволоки, аксиально подаваемой через канал плазмотрона.
Кондрашов, К.А., Макаренко, Н.А., Чигарев, В.В., Воропай, Н.М.   +3 more
core  

Melting ice and cloud electrification [PDF]

, 1971
A vertical wind tunnel has been constructed inside a cold room to simulate the fall of a frozen water drop from the 0 C level in a thundercloud. It was possible to freely support an ice sphere clear of the sides but the particle crashed early in the ...
Martin, Peter F.
core  

Numerical modelling of wire arc additive manufacturing: methods, status, trends, and opportunities

Journal of Physics D: Applied Physics
Wire arc additive manufacturing (WAAM) is a metal additive manufacturing (AM) process attracting interest from the automotive, defence, aerospace, architecture/engineering/construction and other industries because of its ability to manufacture large ...
Yun Hwan Kim, Dayalan R. Gunasegaram, Paul W. Cleary, A. B. Murphy   +3 more
semanticscholar   +1 more source

Dependence between a pulsed wire feeding and its melting speed in short-circuit welding

, 2007
Рассмотрена математическая модель, описывающая зависимость тока дугового процесса и, соответственно, скорости плавления электродной проволоки от изменяющегося характера ее движения в процессе сварки плавящимся электродом, в частности, при коротких ...
Лебедев, В.А.
core   +1 more source