Results 51 to 60 of about 76,744 (301)
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
An investigation on the mechanics of nanometric cutting and the development of its test-bed [PDF]
, 2003 The mechanics of machining at a very small depth of cut (100 nm or less) is not well understood. The chip formation physics, cutting forces generation, resulting temperatures and the size effects significantly affect the efficiency of the process and ...
Luo, X, Cheng, K, Guo, XJ, Holt, R
core +2 more sources
Numerical analysis of hot deep drawing of din 27MNCRB5 steel sheets under controlled stretching [PDF]
, 2013 Hot stamping has been widely studied and increasingly applied in the automotive industry. This process is characterized by its ability to stamp high strength steels, yielding products with high mechanical strength, thus ...
Batalha, Mario H. F., Button, Sergio T.
core
Analytical prediction of part dynamics for machining stability analysis [PDF]
, 2010 An analytical procedure is developed to predict workpiece dynamics in a complete machining cycle in order to obtain frequency response functions (FRF) which are needed in chatter stability analyses.
Alan, Salih +3 more
core +2 more sources
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Study on Material Removal Model by Reciprocating Magnetorheological Polishing
Micromachines, 2021 In this study, a new reciprocating magnetorheological polishing (RMRP) method for a flat workpiece was proposed. Based on the RMRP principle and Preston equation, the material removal rate (MRR) model of the RMRP as well as its normal polishing pressure ...
Rensheng Wang +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Cladding is a proven method that boosts the surface qualities of mechanical parts by applying a layer of more durable material over a base substrate. This work responds to the needs of offshore and pressure vessels sectors by focusing on cladding a super austenitic steel onto low‐carbon steel through gas tungsten arc welding.
E. J. da Cruz Junior +6 more
wiley +1 more source
Determination of heat transfer coefficient for hot stamping process [PDF]
, 2015 © 2015 The Authors.The selection of the heat transfer coefficient is one of the most important factors that determine the reliability of FE simulation results of a hot stamping process, in which the formed component is held within cold dies until fully ...
Fakir, OE, Gao, H, Ji, K, Wang, L
core +1 more source
Nondestructive Testing of Welded Composite Metal Foams
Advanced Engineering Materials, EarlyView.X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva +2 more
wiley +1 more source