Results 131 to 140 of about 7,474,775 (237)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

EIGER2 hybrid-photon-counting X-ray detectors for advanced synchrotron diffraction experiments. [PDF]

J Synchrotron Radiat, 2023
Donath T, Šišak Jung D, Burian M, Radicci V, Zambon P, Fitch AN, Dejoie C, Zhang B, Ruat M, Hanfland M, Kewish CM, van Riessen GA, Naumenko D, Amenitsch H, Bourenkov G, Bricogne G, Chari A, Schulze-Briese C.   +17 more
europepmc   +1 more source

Development of an x-ray excited optical luminescence microscope (XEOM) [PDF]

X-ray excited optical luminescence (XEOL) refers to the trans-visible emission produced as a consequence of X-ray bombardment and provides an alternative detection method for X-ray absorption spectroscopy (XAS). Whereas XAS measured by conventional means
Hand, M. (Matthew)
core  

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Response characteristics of MAPbBr₃ direct conversion X-ray detectors based on measurements and Monte Carlo simulation. [PDF]

Heliyon, 2023
Qin F, Zhao R, Zhu WF, Deng NQ, Jiao ZW, Tang XQ, Wu JJ.   +6 more
europepmc   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Heterostructure engineering for efficient halide perovskite X-ray detectors. [PDF]

iScience
Li F.
europepmc   +1 more source

Nanocrystalline CaWO₄ and ZnWO₄ Tungstates for Hybrid Organic-Inorganic X-ray Detectors. [PDF]

Materials (Basel), 2023
Pudza I, Pudzs K, Tokmakovs A, Strautnieks NR, Kalinko A, Kuzmin A.   +5 more
europepmc   +1 more source