Results 161 to 170 of about 3,858,273 (345)

High‐Entropy Alloy Design Toward Cobalt Substitution for High Hardness and Low Wear Rate Using X–Cr–Fe–Mn–Ni System

Advanced Engineering Materials, EarlyView.
This study explores the replacement of cobalt using the high‐entropy alloy design strategy for wear‐resistant components operating at high temperatures. Starting from the Cantor alloy, cobalt is substituted with Cu, Al, V, or Mo. Metallurgical and tribological analyses reveal that aluminum, vanadium, and molybdenum effectively strengthen the developed ...
Rafaël Jénot, Laurent Peltier, Fodil Meraghni, Mathieu Marquer, Oriane Baulin, Clotilde Macke‐Bart   +5 more
wiley   +1 more source

High‐temperature X‐ray Time‐lapse Imaging Based on the Improved Scintillating Performance of Na₅Lu₉F₃₂:Tb³⁺ Glass Ceramics [PDF]

Rongfei Wei, Ying Chen, Li Wang, Junwei Pan, Xiangling Tian, Fangfang Hu, Hai Guo   +6 more
openalex   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Limitations of dual x-ray absorptiometry in children with chronic kidney disease [PDF]

, 2009
Lutz T. Weber, Otto Mehls
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Structure of sodium above 100 GPa by single-crystal x-ray diffraction

, 2007
M. I. McMahon, Eugene Gregoryanz, L. F. Lundegaard, I. Loa, Christophe L. Guillaume, R. J. Nelmes, Annette Kleppe, M. Amboage, H. Wilhelm, A. P. Jephcoat   +9 more
openalex   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source

Teaching Undergraduates X‑ray Crystallography with Porphyrins. [PDF]

ACS Omega
Toombs A, De La Cruz M, Van Hoosen L, Marr ZY, Redington M, Zurek E, Pham J.   +6 more
europepmc   +1 more source