Results 261 to 270 of about 456,481 (326)

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Internal elemental microanalysis combining x-ray fluorescence, Compton and transmission tomography [PDF]

, 2003
Bruno Golosio, Alexandre Simionovici, Andréa Somogyi, Laurence Lemelle, Marina Chukalina, Antonio Brunetti   +5 more
openalex   +1 more source

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

Reactive Interaction and Wetting of Fe‐ and Mn‐Containing, Secondary AlSi Alloys with Manganese Oxide Ceramic Filter Material for Fe Removal

Advanced Engineering Materials, EarlyView.
Fe‐ and Mn‐containing AlSi alloys undergo aluminothermic reaction with Mn oxide in sessile‐drop and crucible experiments forming poor‐wetting Al2O3 while Mn enriches in the alloy. Primary Fe‐containing particles are preferentially attached to the Mn oxide.
Hanka Becker, Simon Waschull, Beate Fankhänel, Claudia Voigt, Alexandros Charitos, Christos G. Aneziris, Andreas Leineweber   +6 more
wiley   +1 more source

Impact of Hot Isostatic Pressing on Microstructure Evolution and Creep Performance of Powder Bed Fusion–Laser Beam Processed CM247LC

Advanced Engineering Materials, EarlyView.
The influence of Hot Isostatic Pressing (HIP) temperature on the microstructure and creep performance of powder bed fusion–laser beam processed CM247LC superalloy is investigated. Grain growth and γ’ precipitate evolution are characterized following HIP at varying temperatures.
Ahmed Fardan, Johannes Gårdstam, Eva Oscarsson, Håkan Brodin, Eduard Hryha   +4 more
wiley   +1 more source

Asbestos-Related Pleural Abnormalities Detected by Chest X-Ray : Fair Agreement with Detection by Computed Tomography

, 2001
Narufumi SUGANUMA, Yukinori Kusaka, Yomei HIRAGA, Yutaka HOSODA, Hisao SHIDA, Hiroshi MORIKUBO, Toru Matsumoto   +6 more
openalex   +2 more sources

Comparative Study of Experimental Methods for Measuring Thermal Properties of 100Cr6 Steel Powders

Advanced Engineering Materials, EarlyView.
This study investigates the thermal properties of 100Cr6 steel in both bulk and powder forms. Measuring the very low thermal conductivity typically exhibited by powders poses significant challenges. To address this, two novel measurement techniques—temperature gradient and finite laser pulse response—are introduced and evaluated by comparison with the ...
Junsheng Zhuo, Hagen P. Kohl, Dongmei Liu, Lisa Matthäus, Arne Bochmann, Aaron Berger, Sebastian Weber, Stefan Nolte, Stephanie Lippmann   +8 more
wiley   +1 more source

Study of Digital Simultaneous Multi-plane Tomography Using Digital X-ray TV

, 2001
Shu Ikeda, Masao Takahashi, Masayuki Tsuda   +2 more
openalex   +2 more sources

Correlative cryo-soft X-ray tomography reveals defective lysosomes in amyloid-β oligomer treated hippocampal neurons

, 2022
Marshall KE, Mengham K, Spink MC, Vania L, Pollard HJ, Darrow MC, Duke E, Harkiolaki M, Serpell LC.   +8 more
europepmc   +1 more source

Key Trends and Insights in Smart Polymeric Skin Wearable Patches

Advanced Engineering Materials, EarlyView.
Intelligent polymers, which respond to various physical and biological stimuli, are explored for the development of skin wearable patches in biomedical applications. Smart polymers, also known as intelligent or stimuli‐responsive polymers, play a crucial role in the development of advanced wearable patches due to their versatility and softness.
Sergio J. Peñas‐Núñez, Rajat Rai, Miryam Criado‐Gonzalez   +2 more
wiley   +1 more source