Results 271 to 280 of about 7,531,616 (402)

Intensity of Polarised X-Rays [PDF]

, 1935
W. H. George
openalex   +1 more source

Development of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness

Advanced Engineering Materials, EarlyView.
Additive manufacturing of magnesium alloys by laser is difficult because the melting point of the oxide layer is much higher than the evaporation temperature of the metal underneath. Making the oxide layer thinner can solve this problem. Alloying magnesium with strontium makes the oxide layer thinner, especially at 0.5 wt%.
Elmar Jonas Breitbach, Stefan Julmi, Sabine Behrens, Tatiana Blank, Arvid Abel, Nicole Emminghaus, Ludger Overmeyer, Christian Klose, Hans Jürgen Maier   +8 more
wiley   +1 more source

ChestX-Transcribe: a multimodal transformer for automated radiology report generation from chest x-rays. [PDF]

Front Digit Health
Singh P, Singh S.
europepmc   +1 more source

Mechanisms of Increasing Weld Depth during Temporal Power Modulation in High‐Power Laser Beam Welding

Advanced Engineering Materials, EarlyView.
Temporal power modulation increases weld depth in high‐power laser beam welding of dissimilar round bars by nearly 20% compared to same average continuously welded welding power. The mechanism of action also applies to sheet welding and depends on the inertia of keyhole depth for the modulated laser beam power.
Jan Grajczak, David Reynders, Christian Nowroth, Jens Twiefel, Jörg Wallaschek, Sarah Nothdurft, Jörg Hermsdorf, Stefan Kaierle   +7 more
wiley   +1 more source

Clinical value and radiographic features of low dose CT scans compared to X rays in diagnosing mycoplasma pneumonia in children. [PDF]

Sci Rep
Xiao S, Zeng S, Kou Y.
europepmc   +1 more source

X-ray Spectrographic Determination of Strontium [PDF]

, 1959
Jennifer Campbell, H.I. Shalgosky
openalex   +1 more source

Simulation of Inhomogeneous Refractive Index Fields Induced by Hot Tailored Forming Components

Advanced Engineering Materials, EarlyView.
This article presents a simulation model for simulating inhomogeneous refractive index fields (IRIF) in hot‐forged components, accounting for thermal influences and complex geometries. Through this simulation, a priori knowledge about the propagation of the IRIF can be obtained, allowing for the positioning of the component or an optical measurement ...
Pascal Kern, Lennart Hinz, Markus Kästner, Eduard Reithmeier   +3 more
wiley   +1 more source

Retrospective and statistical analysis of hand and forearm injuries in the Silesian pediatric population - study of post-traumatic X-rays in 2022. [PDF]

PLoS One
Machnikowska-Sokołowska M, Ciekalski M, Szymańska I, Mordarski J, Gruszczyńska K.   +4 more
europepmc   +1 more source

Determining the Necessity of Post‐Processing Heat Treatment for the 316L Stainless Steel Manufactured by Laser Powder Bed Fusion through Evaluation of Mechanical and Corrosion Properties

Advanced Engineering Materials, EarlyView.
This article examines the effect of postprocessing heat treatment on 316L stainless steel (SS316L) produced via laser powder bed fusion (LPBF). Heat treatment slightly affects property anisotropy, reduces strength, and enhances elongation. However, it increases corrosion susceptibility due to nanoscale precipitations, though overall corrosion ...
Baibhav Karan, Malar Vadani, Prashanth Muralishankar, Kiomars Moheimani, Ayan Bhowmik, Mingxing Zhang   +5 more
wiley   +1 more source

Radiomics analysis based on plain X-rays to detect spinal fractures with posterior wall injury. [PDF]

Digit Health
Liu W, Zhang X, Tang R, Yu C, Sun G.
europepmc   +1 more source