Results 111 to 120 of about 84,989 (345)

Unraveling the Friction and Wear Characteristics of the High Hardness, Low Young's Modulus 60NiTi Alloy: A Synergistic FEM Simulation and Experimental Study [PDF]

, 2023
Ziming Yin, Lijing Zheng, Jing Li, Bo Li, Hu Zhang   +4 more
openalex   +1 more source

Interconnected Porous Hydrogels with Tunable Anisotropy Through Aqueous Emulsion Bioprinting

Advanced Functional Materials, EarlyView.
A 3D bioprintable microporous bioink is developed using an aqueous two‐phase system (ATPS) composed of extracellular matrix (ECM) mimetic biopolymers. The ATPS bioink enables the fabrication of interconnected porous architectures with up to 70% porosity, supporting long‐term cell viability and 3D cell alignment, enabling a simultaneous generation of ...
Hugo Edgar‐Vilar, Francisca P. Correia, Inês M. Freitas, Vítor M. Gaspar, João F. Mano   +4 more
wiley   +1 more source

Nanohardness and young's modulus of tooth enamel

RUDN Journal of Medicine, 2009
The nanomechanical properties and roughness of tooth enamel are investigated.
I Yu Lebedenko, S D Arutyunov, S A Muslov, A S Useinov   +3 more
doaj  

Selection Strategies for Flexible Pressure Sensor Electrode Materials Toward Ultrafast Response

Advanced Functional Materials, EarlyView.
This study reveals, for the first time, how the electrode–organic interface governs the temporal performance of flexible pressure sensors. By pairing high‐conductivity CVD PEDOT with commonly used metal electrodes, the authors demonstrate that interfacial energy alignment dictates microsecond‐scale response, providing a straightforward design strategy ...
Jinwook Baek, Yuxuan Zhang, Hyeondong Yang, Minyoung Kim, Pavlos P. Vlachos, Jeongok Choe, Bo‐Gyu Bok, Kejie Zhao, Han‐Wook Song, Min‐Seok Kim, Martin Byung‐Guk Jun, Sunghwan Lee   +11 more
wiley   +1 more source

Poisson's ratio in cubic materials

, 2006
Expressions are given for the maximum and minimum values of Poisson's ratio $\nu$ for materials with cubic symmetry. Values less than -1 occur if and only if the maximum shear modulus is associated with the cube axis and is at least 25 times the value of
Norris, Andrew N.
core   +2 more sources

Electrochemically Driven Dissipative Growth of Affinity Hydrogels for Bioresponsive Interfaces

Advanced Functional Materials, EarlyView.
Voltage pulses drive the growth and reinforcement of hydrogel films under dissipative conditions. This biocompatible strategy enables efficient integration of affinity ligands into the hydrogel matrix, enhancing the selective capture of growth factors and allowing precise temporal control over their release, making them well‐suited as adaptive ...
Roberto Baretta, Marco Frasconi
wiley   +1 more source

Controlled Movement of Soft Actuators using Multi‐Responsive Microgel Arrays and Microcirculatory Systems

Advanced Functional Materials, EarlyView.
Microscale hydrogels (microgels) feature improved mass transport characteristics supportive of fast actuation and chemical tunability amenable to programmed stimuli response. A unique soft actuator architecture is realized by encapsulating microgels in soft microcirculatory systems which enable the convenient delivery of liquid stimuli for powering and
Nengjian Huang, Brennan P. Watts, Stephen A. Morin   +2 more
wiley   +1 more source

Determination of hardness and Young's modulus in fcc Cu–Ni–Sn–Al alloys via high-throughput experiments, CALPHAD approach and machine learning

Journal of Materials Research and Technology
Hardness and Young's modulus are critical indicators in the design of innovative Cu–Ni–Sn–Al alloys with desired elastic and strength properties. In this study, the composition-dependent hardness and Young's modulus in the fcc Cu–Ni–Sn–Al alloys were ...
Wenli Zhang, Ying Tang, Jinghan Gao, Lijun Zhang, Jian Ding, Xingchuan Xia   +5 more
doaj   +1 more source

Effect of Kind of Deformation on Young's Modulus, Damage Parameter, Texture and Structure of Alloy Mg – 5% Li (wt)

, 2020
В. В. Усов, H.‐G. Brokmeier, N. М. Shkatulyak, E.S. Savchuk, Norbert Schell   +4 more
openalex   +2 more sources

Adaptive 4D‐Printed Vascular Stents With Low‐Temperature‐Activated and Intelligent Deployment

Advanced Functional Materials, EarlyView.
Microarchitected coronary artery stents were fabricated using a polycaprolactone (PCL)‐based shape memory polymer (SMP) composite via projection micro‐stereolithography (PµSL) 4D printing. By incorporating diethyl phthalate (DEP) as a plasticizer, the thermal transition temperature (Ttran) was modulated to about 37°C, enabling rapid and autonomous ...
Yannan Li, Yifan Pan, Chikahiro Imashiro, Chaolun Xu, Jianxian He, Jingao Xu, Kewei Song, Ze Zhang, Chen Gao, Junbo Jiang, Runhuai Yang, Kayo Hirose, Shinjiro Umezu   +12 more
wiley   +1 more source