Tetragonal zirconia: Wet chemical preparation, mechanical and electrical properties [PDF]
, 1985 Yttria-stabilized zirconia powders were prepared in the composition range of 3 to 13 at% yttria. The hydrolysis-gel precipitation technique was used, starting from metal alkoxides or chlorides.
Burggraaf, A.J. +3 more
core +36 more sources
Effect of ion implantation doping on electrical properties of yttria-stabilized zirconia thin films [PDF]
, 1992 The change in conductivity of Fe and Ti implanted rf-sputtered layers of yttria-stabilized zirconia (YSZ) was studied as a function of the temperature (400–800°C) and oxygen partial pressure. In an oxidized state and in the temperature range of 400–600°C,
Burggraaf, A.J., Hassel, B.A. van
core +3 more sources
Characterization of Fe implanted yttria-stabilized zirconia by cyclic voltammetry [PDF]
, 1992 The technique of cyclic voltammetry has been applied to study reduction and oxidation phenomena which are observed at low oxygen partial pressures during steady state current-overpotential measurements of the Au, O2(g)/Fe implanted yttria-stabilized ...
Burggraaf, A.J., Hassel, B.A. van
core +2 more sources
, 1978 A new, sinterable yttria (Y/sub 2/O/sub 3/) plaster was developed. The properties of this plaster depend on: (1) starting-power characteristics, (2) type and concentration of the acid used for the liquid phase, and (3) the liquid-to powder (L/P) ratios. Physical and chemical properties of the yttria plaster were investigated.
Holcombe, C. E. +2 more
openaire +2 more sources
CVD of solid oxides in porous substrates for ceramic membrane modification [PDF]
, 1992 The deposition of yttria-doped zirconia has been experimented systematically in various types of porous ceramic substrates by a modified chemical vapor deposition (CVD) process operating in an opposing reactant geometry using water vapor and ...
Burggraaf, A.J., Lin, Y.S.
core +2 more sources
Electrode polarization at the Au, O2(g)/yttria stabilized zirconia interface. Part II: electrochemical measurements and analysis [PDF]
, 1991 The impedance of the Au, O2 (g) / yttria stabilized zirconia interface has been measured as function of the overpotential, temperature and oxygen partial pressure. At large cathodic overpotentials (η < −0.1 V) and large anodic overpotentials (η > +0.1 V)
Boukamp, B.A. +2 more
core +3 more sources
X-ray photoemission spectroscopy determination of the InN/yttria stabilized cubic-zirconia valence band offset [PDF]
, 2007 The valence band offset of wurtzite InN(0001)/yttria stabilized cubic-zirconia (YSZ)(111) heterojunctions is determined by x-ray photoemission spectroscopy to be 1.19±0.17 eV giving a conduction band offset of 3.06±0.20 eV.
C. E. Kendrick +8 more
core +2 more sources
Processing of yttrium-doped barium zirconate for high proton conductivity [PDF]
, 2007 The factors governing the transport properties of yttrium-doped barium zirconate (BYZ) have been explored, with the aim of attaining reproducible proton conductivity in well-densified samples.
Babilo, Peter +2 more
core +1 more source
Structural characterization of YBa(2)Cu(3)O(7)/Y(2)O(3) composite films
, 1997 Using 4-circle x-ray diffraction and transmission electron microscopy we have studied the microstructure and in-plane orientation of the phases present in thin film composite mixtures of YBa(2)Cu(3)O(7) and Y(2)O(3).
Broussard, P. R. +2 more
core +1 more source
Effect of 1 wt% LiF additive on the densification of nanocrystalline Y2O3 ceramics by spark plasma sintering [PDF]
, 2011 Densification of nanocrystalline cubic yttria (nc-Y2O3) powder, with 18 nm crystal size and 1 wt% LiF as a sintering additive was investigated. Specimens were fabricated by spark plasma sintering at 100 MPa, within the temperature range of 700–1500 °C ...
Chaim, Rachman +3 more
core +2 more sources