Results 31 to 40 of about 1,969,748 (147)

Recovering Critical Elements From Wastewater for Battery Materials: A Review

open access: yesRare Metals, Volume 45, Issue 7, July 2026.
ABSTRACT Driven by global carbon neutrality goals, the transition toward a circular economy and sustainable resource management has become increasingly imperative. Given the indispensable role of battery technologies in modern energy storage systems, strategic elements such as lithium (Li), cobalt (Co), and nickel (Ni)—identified by the European ...
Ting Lei   +5 more
wiley   +1 more source

35千伏穿缆式变压器瓷套整体成型工艺简介 附视频

open access: yesDianci bileiqi, 1975
变压器用瓷套近几年来采用穿缆式的用户越来越多,这种型式的套管结构有便于密封、节省导体材料等技术经济价值。但由于穿缆式套管的中孔为异形结构,故给电瓷成型工艺造成较大的困难。许多兄弟厂对这类套管采用湿接成型工艺。这种工艺,存在着工序多,生产效率低,质量不稳定,操作技术要求较高等缺点。为了提高工效,稳定产品质量 ...
醴陵电瓷厂技术科
doaj  

Wafer‐Scale Amorphous g‐C3N4 With Broadly Tunable Dielectric Properties for 2D Electronics

open access: yesRare Metals, Volume 45, Issue 7, July 2026.
ABSTRACT Two‐dimensional (2D) semiconductors are regarded as promising candidates for next‐generation electronics due to their superior electrostatic control; however, their performance is severely constrained by the lack of suitable dielectric materials.
Binyin Gao   +13 more
wiley   +1 more source

多棱勾形仿型修坯刀的设计

open access: yesDianci bileiqi, 1982
一、概况随着大泄漏比耐污型绝缘子的发展,对制坯成型用刀具提出了新的要求。近几年,我厂工艺科、工具科及大型车间通过反复实践,不断完善,设计制造了一批多棱勾形仿型修坯刀(简称勾修刀),自投入生产以来,基本满足了工艺要求,为成型刀具的创新迈开了一步。
刘大震
doaj  

Multi‐Site Chelation Enabled by 3D‐Printed TiO2 Hydrogel Monoliths for Dynamic Ge(IV) Recovery in Fixed Beds

open access: yesRare Metals, Volume 45, Issue 7, July 2026.
ABSTRACT Germanium is a critical dispersed metal, yet sustainable recovery from dilute solutions is limited by sorbents that are difficult to regenerate and operate in continuous mode. Here, we fabricate a regenerable 3D‐printed hydrogel monolith (3D‐ATO‐GS) by integrating hydroxyl‐rich amorphous TiO2 nanoparticles into an alginate/gelatin scaffold ...
Wenhuan Guo   +6 more
wiley   +1 more source

110kV电容套管瓷套光坯表面开裂产生的原因及防止开裂的措施 附视频

open access: yesDianci bileiqi, 1998
在泥料可塑性下降的情况下,按原有成型工艺成型,会造成瓷套光坯表面开裂。在泥料可塑性一时无法改善的情况下,改进成型工艺,即减小粗修量,改善伞面出现的疏松结构,粗修的余量待精修时修去,精修后再精心抹坯,可防止光坯表面开裂。
顾瑞云, 蔡海龙
doaj  

Influence of Alkaline Earth Barium on the Microstructure, Corrosion Behavior, and Cytocompatibility of Biodegradable Zinc

open access: yesRare Metals, Volume 45, Issue 7, July 2026.
ABSTRACT Biodegradable Zn‐based alloys are promising candidates for temporary implants, yet excessive Zn2+ release during degradation may induce cytotoxicity and adverse tissue responses. In this study, Zn‐xBa alloys (x = 0.1 wt%, 0.5 wt%, 1.0 wt% and 3.0 wt%) were developed to achieve controlled corrosion behaviors with improved biocompatibility.
Liu‐Dang Fang   +9 more
wiley   +1 more source

堤下爆炸法处理淤泥地基新工艺的理论、实验及工程应用(Ⅰ)堤下爆炸法的理论及实验研究

open access: yes, 1999
在淤泥质海岸建造高桩码头,通常在开挖基槽后沉桩再抛石形成棱体。基槽中的回淤淤泥很难清除,为此研制了堤下爆炸挤淤新工艺。本文是关于该新工艺的理论、实验及工程应用的一个总结,分两部分,第一部分着重介绍挤淤机理、装药工艺、模型律及药量公式等。研究及应用表明,这种新工艺与先前我们研制成功的爆夯法及爆填法一起 ...
张加华, 杨振声
core   +2 more sources

Synergistic Dual‐Defect Engineering in Amorphous‐Nanocrystalline Heterostructures for Accelerated Oxygen Evolution

open access: yesRare Metals, Volume 45, Issue 7, July 2026.
ABSTRACT Defect engineering has been widely demonstrated as an effective strategy for enhancing the activity of OER metal catalysts, among which the introduction of twin boundaries (TBs) has proven particularly efficient. However, single‐type defects offer limited performance enhancement.
Wentao Cai   +11 more
wiley   +1 more source

贝壳软化与成型工艺

open access: yes, 1987
贝壳软化与成型工艺待填
待填写
core  

Home - About - Disclaimer - Privacy