Results 51 to 60 of about 14,414 (189)
World Water Policy, Volume 10, Issue 3, Page 971-985, August 2024.Abstract Quality water is essential to people's health and social and economic well‐being. Evaluation of the quality of the water sources provides benchmark data on quality status and insights into the development of further protective measures. A laboratory‐based cross‐sectional study design was conducted in the diarrheal hotspot area of the North ...
Tsegahun Asfaw Abebe +5 more
wiley +1 more source
Veterinary Dermatology, Volume 35, Issue 3, Page 325-336, June 2024.Background – Norway spruce (Picea abies) resin‐based products are used in human medicine. A resin‐based otic rinse also could be useful in supportive care of canine otitis externa (COE), yet information on its antimicrobial effect against canine pathogens or ototoxicity is lacking.
Elina Aimo‐Koivisto +5 more
wiley +1 more source
Zhongshan Daxue xuebao. Yixue kexue ban, 2012 【目的】 探讨SENP-1和HIF-1α在肝细胞肝癌组织,癌边缘组织及非癌组织中的表达与肝癌发展的关系和在肝癌新生血管生成中的作用.【方法】 应用RT-PCR、荧光定量PCR和免疫组织化学方法检测57例肝癌组织,癌边缘组织,非癌组织中SENP-1和HIF-1α的表达,用CD34多克隆抗体标记新生血管内皮细胞,计数微血管密度(MVD),分析三者表达的相关性及与相关临床病理参数的关系.【结果】 肝癌组织与癌边缘组织SENP-1、HIF-1αmRNA表达显著高于非癌组织,SENP-1和HIF ...
李湘竑 +5 more
doaj
Kinetic Investigations and Experimental Determination of Phase Equilibria in some Nickle-Based superalloys [PDF]
, 2016 镍基高温合金具有优异的综合性能，能够适应长时间的高温环境服役要求，广泛应用于航空工业中，其中航空发动机中的镍基高温合金用量最高，所用比例达到了40%-50%。随着航空工业的不断发展，航空发动机对工作温度、推重比及使用寿命的要求进一步提高，高温合金的成分设计面临着新的挑战。相图和动力学计算是材料设计的基础，它使材料工作者摆脱了过去低效的“炒菜式”的材料设计理念，对高温合金的设计研发具有重要的意义。本研究采用扩散偶法，对Ni-Co-Al三元体系的扩散行为进行了研究；基于文献中的实验数据，对Ni-W-X(X ...
杨应来
core
Microstructure and impact toughness of hot rolled and tempered low carbon bainitic steel AH80DB [PDF]
, 2016 The microstructure,martensite/austenite(M/A) islands,precipitated phases,high-angle grain boundaries and effective grain size of hot rolled and tempered low carbon bainitic steel AH80 DB were studied by scanning electron microscopy(SEM),transmission ...
DING Yi +6 more
core +1 more source
Zhongshan Daxue xuebao. Yixue kexue ban, 1997 摘 要 将钛涂层317L 接骨板植入电子线照射的犬右下颌骨体部, 用透射电镜(TEM)观察相邻骨膜超微 结构变化, 结果显示, 钛涂层317L 接骨板组相邻骨膜超微结构损伤比未喷涂钛层的317L 接骨板对照组轻微。 可能与未喷涂钛层的317L 接骨板所释放出来的毒性较大的C r 、Ni 离子对组织细胞的再损伤有关, 而钛涂层 317 L 接骨板表面呈纯钛相, 不会造成组织细胞超微结构明显损伤。
李少萍 朱明仁 姚小武 殷学民 任材年
doaj
Comparison between the microstructures of M2 steel cast by the water-cooled copper mould and the sand mould [PDF]
, 2016 M2 steel was melted by a 25 kg high-frequency vacuum induction furnace and was cast to ingots with a cross section of 100 mm×50 mm by the water-cooled copper mould and the sand mould.The effects of cooling rate on the ingot's secondary dendrite arm ...
CHOU Sheng-tao, ZHAO Zhi-gang, ZHU Rong
core +1 more source
Zhongshan Daxue xuebao. Yixue kexue ban, 2007 【目的】探讨大鼠牙囊细胞体外培养的方法。【方法】分离出大鼠牙囊组织,分别采用组织块培养法、细胞消化分散法、及改良组织块法进行牙囊细胞原代及传代培养,倒置相差显微镜下进行细胞形态学观察,透射电镜观察细胞超微结构。【结果】培养至第3天,倒置相差显微镜观察发现,采用组织块培养法,见少数细胞从组织块爬出;而细胞消化分散法则可获得数量多的牙囊细胞,但与杂质细胞混杂生长;改良组织块法见量多、相对纯的牙囊细胞。电镜下牙囊细胞无桥粒,胞浆中含有高密度电子颗粒和大量粗面内质网。组织块法 ...
谷海晶, 凌均棨, 杜宇
doaj
Friction and wear properties of ultrafine grain Ti-8Mo-3Fe alloys fabricated by MA-SPS [PDF]
, 2017 The friction and wear properties of ultrafine grain Ti-8Mo-3Fe alloy fabricated by mechanical alloying (MA) and subsequent spark plasma sintering (SPS) were investigated in SBF simulated body fluid.
LU Xin +4 more
core +1 more source