Results 11 to 20 of about 20,019 (130)
, 1984 前言残余应力对疲劳的影响是长期以来人们十分关注的课题,因为人们逐渐认识到许多疲劳现象都与残余应力相关。例如疲劳裂纹的形成与扩展、少数极高应力、平均应力、加载次序、裂纹迟滞效应、缺口应力集中等都与残余应力有密切关系。残余应力是影响疲劳的一个重要因素。因此,弄清残余应力的大小和分布,以及残余应力与上述疲劳现象之间的关系 ...
曾春华
core +2 more sources
, 2008 本文选择纳米晶与粗晶镍为实验材料,对其疲劳行为进行了实验研究。结果表明,纳米晶镍具有比粗晶镍更高的疲劳极限。AFM结果表明纳米晶疲劳后表面出现胞状起伏,晶粒尺寸没有发生明显改变 ...
谢季佳, 洪友士
core +2 more sources
, 1980 疲劳问题跟工程机械和其它工业部门有着极为密切的关系。几乎所有工程机械都受重复交变载荷的作用,因而普遍存在着疲劳问题。据统计,工程机械大多数构件的破坏都是由于疲劳引起的 ...
曾春华
core +2 more sources
Rare Metals, Volume 45, Issue 9, September 2026.ABSTRACT Aiming at the problems of insufficient forming quality and poor surface performance in the preparation of Ti‐6Al‐4V alloy by laser powder bed fusion (LPBF), this study proposed a laser in situ forging additive manufacturing (LIF‐AM) technology, which integrates LPBF with femtosecond laser in situ shock forging and realizes defect control and ...
Peng He +10 more
wiley +1 more source
Rare Metals, Volume 45, Issue 9, September 2026.ABSTRACT TiN films deposited by physical vapor deposition (PVD) are widely used as protective films due to their high hardness and wear resistance. However, their application under high‐load conditions is limited by poor load‐bearing capacity and susceptibility to spalling on soft substrates.
Ziyu Wang +6 more
wiley +1 more source
Rare Metals, Volume 45, Issue 7, July 2026.ABSTRACT Laser powder bed fusion (LPBF) of Inconel 718 alloy inevitably introduces pronounced microstructural anisotropy, typified by columnar grains and robust crystallographic texture. This results in direction‐dependent fatigue behavior, raising critical reliability concerns for high‐stakes aerospace applications.
Zhifang Shi +9 more
wiley +1 more source
Rare Metals, Volume 45, Issue 5, May 2026.ABSTRACT The inherent brittleness of hardmetals stems from the rigid covalent bond in the ceramic matrix and the sharp ceramic/metal interface, which restricts the nucleation and motion of dislocations. In this study, a novel strategy is proposed to activate significant dislocation behaviors in the WC matrix by employing a non‐equiatomic CoNiFeCr ...
Cheng Qian +9 more
wiley +1 more source
, 2016 近些年来,超高周疲劳研究越来越受到国内外学者的重视,而超声疲劳试验机的发展为研究材料的超高周疲劳带来了巨大的便利。与常规频率下的传统疲劳实验相比,超声疲劳实验技术大大节约了实验时间,已成为研究超高周疲劳不可或缺的一项实验技术。但与此同时,超声频率也给疲劳研究带来了一些问题,例如超声频率可能导致疲劳强度和寿命的提高、试样温度的升高等,为便于研究,将其统称为频率效应。本文以高强钢GCr15为例,分别在旋转弯曲疲劳试验机、高频疲劳试验机和超声疲劳试验机上进行了三种不同加载频率(52.5 Hz、260 Hz ...
胡远培, 洪友士
core +2 more sources
Gaoya dianqi, 2013 零件疲劳分析与计算对高压开关设备寿命预测起着至关重要的作用。笔者分析了高压开关传动系统关键零件疲劳的特点;建立了零件疲劳极限应力图模型,采用该模型可以计算出零件的疲劳极限与疲劳安全系数,并且可以估算在考虑安全系数前提下零件的疲劳寿命;以某高压断路器传动连杆的疲劳计算为例,对所采用的方法进行了验证。得出了3点结论:①有必要对高压开关零件进行疲劳分析和计算;②借助零件疲劳极限应力图可以较好地进行零件疲劳强度计算;③应力集中和零件材质对疲劳极限和寿命有较大的影响。
程立 +4 more
doaj
Rare Metals, Volume 45, Issue 5, May 2026.ABSTRACT Laser powder bed fusion (LPBF) can fabricate high‐entropy alloys (HEAs) with refined microstructure and enhanced mechanical properties. However, the deformation and fatigue mechanisms of Al‐containing HEAs produced by LPBF remain unclear. In this work, we systematically investigate the tensile properties, deformation mechanisms, and high‐cycle
Dan Zheng +4 more
wiley +1 more source