Results 171 to 180 of about 74,346,148 (200)
Some of the next articles are maybe not open access.

Experimental investigation on selective laser melting of 17-4PH stainless steel

Optics & Laser Technology, 2017
Abstract Selective laser melting (SLM) is an additive manufacturing (AM) technique that uses powders to fabricate 3Dparts directly. The objective of this paper is to perform an experimental investigation of selective laser melted 17-4PH stainless steel. The investigation involved the influence of separate processing parameters on the density, defect,
Zhiheng Hu   +3 more
openaire   +1 more source

Effect of ECAP on the Microstructure and Mechanical Properties of 17-4PH Stainless Steel

Materials Science Forum, 2010
Experiments were conducted to evaluate the influence of equal-channel angular pressing (ECAP) on the microstructure and mechanical properties of 17-4PH steel. The 17-4PH steel was solution-treated at 1040°C for 1h followed by oil cooling before ECAP process.
Gang Yang, Feng Shi Yin
openaire   +1 more source

Inhibitive Effect of Nitrate on Pitting Corrosion of 17-4PH Stainless Steel

Corrosion, 2016
In this work, the inhibition effect of nitrate on the pitting corrosion of 17-4PH stainless steel was investigated in the chloride solution. Potentiodynamic and potentiostatic techniques were used to measure the pitting potential and induction time in various concentrations of chloride and nitrate ions.
M. Seyedi   +4 more
openaire   +1 more source

Effect Of Cold Deformation On Pitting Initiation Of 17-4PH Stainless Steel

ECS Meeting Abstracts, 2013
Abstract not Available.
Davood Nakhaie, Mohammad Hadi Moayed
openaire   +1 more source

Additive manufacturing of 17-4PH stainless steel

2nd International PhD Student’s Conference at the University of Life Sciences in Lublin, Poland: ENVIRONMENT – PLANT – ANIMAL – PRODUCT, 2023
Aleksander Świetlicki   +2 more
openaire   +1 more source

Microstructure and hardness investigation of 17-4PH stainless steel by laser quenching

Materials Science and Engineering: A, 2012
Abstract Surface hardening of 17-4PH was achieved by laser transformation hardening using 5 kW continuous wave CO 2 laser system. The microstructure of the laser-quenched sample was investigated by optical microscopy, transmission electron microscope and 57 Fe Mossbauer spectrometer. The hardness profile was determined by a Vickers hardness tester.
Zhaoyun Chen   +2 more
openaire   +1 more source

Influence of Sulfur Content on the Corrosion Resistance of 17-4PH Stainless Steel

Journal of Materials Engineering and Performance, 2017
According to specification standards, the basic chemical composition of steel 17-4PH for special and critical applications is 15-17% Cr, 3.0-5.0% Ni, 3.0-5.0% Cu, 0.07% C (max) and 0.15-0.45% (Nb + Ta) (wt.%). The maximum sulfur content is 0.030%. However, as it will be shown in this work, this maximum limit for sulfur is too high for services where ...
S. S. M. Tavares   +3 more
openaire   +1 more source

EFFECT OF CASTING DEFECT ON MECHANICAL PROPERTIES OF 17-4PH STAINLESS STEEL

International Journal of Modern Physics B, 2006
Damage and integrity evaluation techniques should be developed steadily in order to ensure the reliability and the economic efficiency of gas turbine engines. Casting defects may exist in most casting components of gas turbine engines, and the defects could give serious effect on mechanical properties and fracture toughness.
JONG-YUP KIM   +2 more
openaire   +1 more source

Influence of Feed Variation on Tool Wear When Milling Stainless Steel 17-4Ph

Journal of Engineering for Industry, 1994
This paper presents the results of experimental studies on the influence of feed variation on tool wear during face milling. Experimental results on milling Stainless Steel 17-4PH show that it is possible to increase tool life substantially with a proper variation of the cutting feed rate throughout the cutting process.
E. Ennajimi, M. Balazinski
openaire   +2 more sources

Microstructure characteristics of segregation zone in 17-4PH stainless steel piston rod

Journal of Iron and Steel Research International, 2017
The segregation of Cu and Ni in a 17-4PH stainless steel piston rod has been confirmed to be responsible for the cracking after heat treatment. Further investigation showed that the segregation zone was composed of three layers, namely the fine grain martensitic layer, the coarse grain martensitic layer and the coarse grain austenitic layer from the ...
Jia-long Tian   +5 more
openaire   +1 more source

Home - About - Disclaimer - Privacy