Results 91 to 100 of about 4,626,402 (194)

3D printing conditions determination for feedstock used in fused filament fabrication (FFF) of 17-4PH stainless steel parts

Metalurgija, 2018
Fused filament fabrication combined with debinding and sintering could be an economical process for 3D printing of metal parts. In this study, compounding, filament making and FFF processing of a feedstock material containing 55 vol.
J. Gonzalez-Gutierez, D. Godec, R. Guráň, M. Spoerk, C. Kukla, C. Holzer   +5 more
doaj  

Sintering Behavior of Bi-Material Micro-Component of 17-4PH Stainless Steel and Yttria-Stabilized Zirconia Produced by Two-Component Micro-Powder Injection Molding Process. [PDF]

Materials (Basel), 2022
Basir A, Sulong AB, Jamadon NH, Muhamad N.   +3 more
europepmc   +1 more source

Effects of Time on Microstructure and Erosion Corrosion behaviour of Liquid nitrided 17-4PH stainless steel

工程科学与技术, 2013
:Liquid nitriding of 17-4 PH martensitic precipitation hardening stainless steels was conducted at 430 °C for different time using a complex chemical heat-treatment, and the erosion corrosion resistance of the nitrided samples was evaluated. Experimental
wang jun
doaj  

Effect of Layer Directions on Internal Structures and Tensile Properties of 17-4PH Stainless Steel Parts Fabricated by Fused Deposition of Metals. [PDF]

Materials (Basel), 2021
Abe Y, Kurose T, Santos MVA, Kanaya Y, Ishigami A, Tanaka S, Ito H.   +6 more
europepmc   +1 more source

Data-driven parameter optimization for bead geometry in wire arc additive manufacturing of 17-4 PH stainless steel

Journal of Advanced Joining Processes
Due to its high strength, corrosion resistance, and toughness, 17-4 Precipitation Hardening (PH) stainless steel is widely used in aerospace, petrochemical, and marine industries. Additive manufacturing (AM) technologies enable the fabrication of complex
Muhammad Irfan, Yun-Fei Fu, Shalini Singh, Sajid Ullah Butt, Abul Fazal Arif, Osezua Ibhadode, Ahmed Qureshi   +6 more
doaj   +1 more source

Plasma debinding and sintering of metal injection moulded 17-4PH stainless steel

Materials Research, 2011
In this work, 17-4PH stainless steel parts processed in a Plasma Assisted Debinding and Sintering (PADS) furnace were characterised in terms of microstructure, final density, microhardness, carbon content and tensile behaviour. To determine whether these
Renan Schroeder, Gisele Hammes, Cristiano Binder, Aloisio Nelmo Klein   +3 more
doaj  

Effect of N Content on Ferrite Phase and Properties of  Maraging Stainless Steel 17-4 PH

Teshugang, 2019
The tested stainless steel 17-4PH (/% : 0.02 ~ 0. 03C, 0.40 ~ 0.50Si, 0.41 ~0. 60Mn, 0.018 ~ 0. 026P, 0. 001S, 15. 56 ~ 15.75Cr, 4. 31 ~ 4. 50Ni, 3. 21 ~ 3.40Cu, 0. 20 ~ 0.25Nb, 0. 013 〜0.
史咏鑫, 马胜斌, 才丽娟, 李青, 张欣杰, 冯文静   +5 more
doaj  

Effect of printing process parameters on tensile strength and wear rate of 17-4PH stainless steel deposited using SLM process

Fracture and Structural Integrity
In the current work 17-4PH Stainless Steel is deposited using SLM process. It is widely used to build structural parts appropriate for automotive, medical, and aerospace applications. The 17-4 PH SS samples were deposited using technical parameters such
Priya Sahadevan , Pon Selvan Chithirai, Avinash Lakshmikanthan, Amiya Bhaumik, Agustin Flores Cuautle   +4 more
doaj   +1 more source

86th Annual Meeting of the Meteoritical Society (2024)

Meteoritics &Planetary Science, Volume 59, Issue S1, Page A1-A468, August 2024.
wiley   +1 more source

Alternative to Nitric Acid Passivation of 15-5 and 17-4PH Stainless Steel Using Electrochemical Techniques. [PDF]

Materials (Basel), 2020
Lara-Banda M, Gaona-Tiburcio C, Zambrano-Robledo P, Delgado-E M, Cabral-Miramontes JA, Nieves-Mendoza D, Maldonado-Bandala E, Estupiñan-López F, G Chacón-Nava J, Almeraya-Calderón F.   +9 more
europepmc   +1 more source