Results 81 to 90 of about 4,567,195 (228)

Six-channel laser single-channel coaxial wire feeding: anisotropy study of component gradient material for 316L and 17-4 PH stainless steel

Journal of Materials Research and Technology
A martensitic 17-4 PH stainless steel wire was processed via additive manufacturing using a six-channel laser system. The wire was then replaced mid-process with an austenitic 316 L stainless steel wire to continue printing, ultimately resulting in the ...
Xianwen Yang, Ruidi Li, Fangda Xu, Jingren Zhi, Shengxing Zhi, Benyin Zhu, Tiechui Yuan   +6 more
doaj   +1 more source

Characterization of CrMnNi Steel Powders Obtained via Gas Atomization

steel research international, Volume 96, Issue 5, May 2025.
In this research article, the dependence of the properties of stainless‐steel powders obtained by gas atomization on the particle size is shown. Also, in this article, the morphology, particle size distribution, microstructure, and phase composition, as well as the change in chemical composition and surface tension of various powders fraction, are ...
Anastasiia Sherstneva, Caroline Quitzke, Matheus R. Bellé, Marco Wendler, Olena Volkova   +4 more
wiley   +1 more source

Densification, deformation, and delamination during co‐sintering process of metal–ceramic laminates

Journal of the American Ceramic Society, Volume 108, Issue 2, February 2025.
Abstract Today, there is a high demand and increasing trend for multifunctional composite materials and components due to the combination of a wide range of favorable properties. However, undesired deformation leading to delamination, curvature, cracks, or even complete fracture frequently occurs during the co‐sintering process of metal–ceramic ...
Chao Liu, Yuanbin Deng, Daniel Gruner, Anke Kaletsch, Tim Gestrich, Christoph Broeckmann   +5 more
wiley   +1 more source

Understanding the Effects of Manufacturing Attributes on Damage Tolerance of Additively Manufactured Parts and Exploring Synergy Among Process‐Structure‐Properties. A Comprehensive Review

Engineering Reports, Volume 6, Issue 11, November 2024.
ABSTRACT Additive Manufacturing (AM) has revolutionized the production industry by offering design freedom with shorter lead times and reduced material wastage. However, the damage tolerance (DT) of AM parts is a significant concern due to their microstructural and geometric complexities, which affect their mechanical performance.
Zia Uddin, Muhammad Muteeb Butt, Varma Kvvssn, Metin U. Salamci, Hüseyin Kizil   +4 more
wiley   +1 more source

Process Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel

Advanced Materials Technologies, Volume 9, Issue 15, August 7, 2024.
A novel QT17‐4+ stainless steel powder is used in directed energy deposition (DED), for the first time. Process parameters are optimized by the response surface methodology (RSM). The microstructure, level of porosity, phase content, and anisotropy in mechanical properties are characterized.
Vyas Mani Sharma, Vladimir Popov, Amir R. Farkoosh, Dieter Isheim, David N. Seidman, Noam Eliaz   +5 more
wiley   +1 more source

Corrosion Fatigue of 17-4pH Stainless Steel in a Simulated Sea Water Solution

Journal of Advanced Materials in Engineering, 2019
Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and
M. Ghasemian Malakshah, F. Ashrafizadeh, A. Eslami, F. Fadaeifard   +3 more
doaj  

Study the potential of micro laser sintering additive manufacturing technology for metallic 3D printing horn antenna structure

The Journal of Engineering, Volume 2024, Issue 8, August 2024.
Abstract Applications for an antenna structure produced with additive manufacturing technology are numerous and promising. This study focuses explicitly on utilizing micro‐laser sintering (MLS) three‐dimensional (3D) printing technology to fabricate two rectangular horn antennas identical to a standard Pasternack® horn antenna, making the fabrication ...
Sheikh Dobir Hossain, Bhushan Lohani, Ryan M. Price, Robert Christopher Roberts   +3 more
wiley   +1 more source

Characterization of the Corrosion of Nanostructured 17-4PH Stainless Steel by Surface Mechanical Attrition Treatment (SMAT)

, 2019
The corrosion properties of nanostructured 17-4PH stainless steel facilitated by a surface mechanical attrition treatment (SMAT) process were studied using electrochemical measurements in 0.6 M NaCl aqueous solution.
Olugbade, Temitope Olumide; id_orcid, Lu, Jian   +1 more
core   +1 more source

Influence of stress ratio on the torsional fatigue behaviour of 17-4PH stainless steel used for biomedical applications [PDF]

, 2019
Precipitation-hardened chromium-nickel-copper stainless steel 17-4PH has a high strength, toughness and good corrosion resistance. According to these features, the 17-4PH stainless steel has a great application in biomedical advices such as hand tools ...
Chehrehrazi, Seyedmasoud
core   +1 more source

Corrosion fatigue of a superduplex stainless steel weldment [PDF]

, 2004
Superduplex stainless steels have superior mechanical and corrosion properties compared to austenitic stainless steels such as the grade 300 series. This is a result of a microstructure consisting of roughly equal percentages of austenite (y) and ferrite
Comer, Anthony John
core   +2 more sources