Results 281 to 290 of about 2,440,522 (332)
Some of the next articles are maybe not open access.
Self-Powered 380 V DC SiC Solid-State Circuit Breaker and Fault Current Limiter
IEEE transactions on power electronics, 2019This paper presents a new ultrafast dc solid-state circuit breaker (SSCB) that uses a silicon carbide cascode as the main switching and limiting semiconductor and an isolated photovoltaic driver to control it.
D. Marroquí +3 more
semanticscholar +1 more source
Preparative Biochemistry & Biotechnology, 2018
In the downstream process of recombinant hepatitis B surface antigen (rHBsAg), nano-colloidal silica adsorbent (Aerosil-380) is one of the possible methods to separate the antigen from other main impurities partially.
S. Hosseini +4 more
semanticscholar +1 more source
In the downstream process of recombinant hepatitis B surface antigen (rHBsAg), nano-colloidal silica adsorbent (Aerosil-380) is one of the possible methods to separate the antigen from other main impurities partially.
S. Hosseini +4 more
semanticscholar +1 more source
Alloy Digest, 2018
Abstract MHZ 380 (mininum yield strength of 380 MPa) is one of a series of microalloyed cold forming steels. The high-strength properties result from precipitation hardening thanks to finely-dispersed carbonitrides and a fine-grained microstructure.
openaire +1 more source
Abstract MHZ 380 (mininum yield strength of 380 MPa) is one of a series of microalloyed cold forming steels. The high-strength properties result from precipitation hardening thanks to finely-dispersed carbonitrides and a fine-grained microstructure.
openaire +1 more source
Alloy Digest, 1991
Abstract ALLOY 380 is an aluminum/silicon die casting alloy with controlled copper content (3-4%). This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fatigue.
openaire +1 more source
Abstract ALLOY 380 is an aluminum/silicon die casting alloy with controlled copper content (3-4%). This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fatigue.
openaire +1 more source
Alloy Digest, 2021
Abstract Industeel Mars 380 (earlier known as Industeel Mars 190) is a low-carbon, Ni-Cr-Mo-V-B, alloy protection steel that is used in the quenched and tempered condition (typical hardness = 380 HBW). It is used as rolled homogeneous armor for ballistic protection and evaluation of armor-defeating ammunition.
openaire +1 more source
Abstract Industeel Mars 380 (earlier known as Industeel Mars 190) is a low-carbon, Ni-Cr-Mo-V-B, alloy protection steel that is used in the quenched and tempered condition (typical hardness = 380 HBW). It is used as rolled homogeneous armor for ballistic protection and evaluation of armor-defeating ammunition.
openaire +1 more source
Alloy Digest, 2015
Abstract PERFORM 380 is one of the Perform series of steels, which are low carbon micro-alloyed steels that are thermomechanically rolled. The 380 in the title refers to the minimum yield strength in MPa (55 ksi). The USA equivalent is Perform 55.
openaire +1 more source
Abstract PERFORM 380 is one of the Perform series of steels, which are low carbon micro-alloyed steels that are thermomechanically rolled. The 380 in the title refers to the minimum yield strength in MPa (55 ksi). The USA equivalent is Perform 55.
openaire +1 more source
Absorption spectrum (380-700 nm) of pure water. II. Integrating cavity measurements.
Applied Optics, 1997R. Pope, E. Fry
semanticscholar +1 more source