Results 271 to 280 of about 309,106 (351)

Investigation of mechanical, kinetic and corrosion properties of borided AISI 304, AISI 420 and AISI 430

Surface Engineering, 2021
In this study, three different types of stainless steels, AISI 304, AISI 420, and AISI 430 were pack borided under 850 °C–925 °C–1000 °C for 2, 4, and 6 h, respectively.
Turker Turkoglu, I. Ay
semanticscholar   +1 more source

High strength and plasticity of AISI 430 ferritic stainless steel achieved by a recrystallization annealing before quenching and partitioning process

, 2021
AISI 430 ferritic stainless steels treated by traditional bell furnace annealing exhibit good plasticity but low strength, which limits its application range. A new heat treatment process, a recrystallization annealing and quenching and partitioning (Q&P)
L. Meng, Hui-hu Lu, Wen-qi Li, Hong-Kui Guo, Jing Tian, W. Liang   +5 more
semanticscholar   +1 more source

Microstructure evolution and corrosion behavior of dissimilar 304/430 stainless steel welded joints

Journal of Manufacturing Processes, 2020
Microstructure and corrosion behavior of dissimilar welds between austenitic stainless steel AISI 304 and ferritic stainless steel AISI 430 were investigated. The phase evolution within each weld was analyzed using thermodynamics calculation and electron
Caimei Wang, Yang Yu, Jianxing Yu, Yu Zhang, Yan Zhao, Qi-Ming Yuan   +5 more
semanticscholar   +1 more source

Joining and characterization of SS-430 using microwave hybrid heating technique

, 2021
Purpose The purpose of this paper is to based upon the joining and characterization (mechanical and metallurgical) of ferritic stainless steel (SS)-430 using a microwave hybrid heating (MHH) phenomenon.
N. Somani, Navjot Singh, N. Gupta
semanticscholar   +1 more source

Effect of natural oxide film on the deuterium permeation behavior of 430 stainless steel

Fusion Engineering and Design, 2020
The deuterium permeation behavior of palladium-coated 316L stainless steel and 430 stainless steel was studied by the gas permeability testing device in this study.
Hongtao Huang, Shuo Ding, Weijun Wang
exaly   +2 more sources

XPS fast depth profile of the native oxide layers on AISI 304, 316 and 430 commercial stainless steels and their evolution with time

, 2020
The thin oxide layers forming on the metal surfaces of metals determine their interactions with the environment and have a strong influence on the materials properties such as corrosion resistance.
S. Detriche, S. Vivegnis, J. Vanhumbeeck, A. Felten, P. Louette, F. Renner, J. Delhalle, Z. Mekhalif   +7 more
semanticscholar   +1 more source

Growth of nanocrystalline β-Nb2N coating on 430 ferritic stainless steel bipolar plates of PEMFCs by disproportionation reaction of Nb(IV) ions in molten salt

Corrosion Science, 2020
It has been attempted to prepare niobium coating for AISI 430 ferritic stainless steel (430 FSS) as bipolar plates of proton exchange membrane fuel cells (PEMFCs) by disproportionation reaction of Nb(IV) ions in molten NaCl-KCl-NaF under Ar atmosphere ...
Lingxu Yang, Ruijia Liu, Ying Wang, Hui Jun Liu, C. Zeng, Chaoqiang Fu   +5 more
semanticscholar   +1 more source

Performance of Co Ni O spinel oxide coating on AISI 430 stainless steel as interconnect for intermediate temperature solid oxide fuel cell

International Journal of Hydrogen Energy, 2017
Jinlong Cui, Lixia Wang, Juncai Sun
exaly   +2 more sources

High temperature oxidation and chromium volatilisation of AISI 430 stainless steel coated by Mn-Co and Mn-Co-Cu oxides for SOFC interconnect application

, 2020
An AISI 430 stainless steel was coated by Mn-Co and Mn-Co-Cu oxides, then tested in O2-5%H2O at 800 °C. The coated samples had reduced rates of oxidation and Cr loss due to Cr-species volatilisation with the higher rates for the Mn-Co-Cu oxide coated ...
Thammaporn Thublaor, S. Chandra-ambhorn
semanticscholar   +1 more source

Crack initiation and life estimation for 316 and 430 stainless steel specimens by means of a critical plane approach

, 2020
In the present paper, the fatigue behaviour of two stainless steels is analysed by employing the criterion by Carpinteri et al. Such a criterion has already been applied to many data related to different metals, but the novelty of this paper is its ...
S. Vantadori, A. Carpinteri, R. Luciano, C. Ronchei, D. Scorza, A. Zanichelli, Y. Okamoto, S. Saito, Takamoto Itoh   +8 more
semanticscholar   +1 more source