Results 31 to 40 of about 1,354 (164)

A Comparative Study of Residual Stress and Mechanical Properties for FSW and TIG Weld on Structural Steel [PDF]

open access: yesArchives of Metallurgy and Materials, 2018
Mechanical properties and residual stresses of friction stir welded and autogenous tungsten inert gas welded structural steel butt welds have been studied.
P.K. Chaurasia   +2 more
doaj   +1 more source

Intelligent modeling using genetic algorithm for optimizing a-tig welding process parameters of mod. 9Cr-1Mo steel [PDF]

open access: yesComputer Methods in Materials Science, 2011
Modified 9Cr-1Mo ferritic steel is used as structural material for stream generator components of power plants. Generally, Tungsten Inert Gas (TIG) welding is preferred for welding these steels in which the depth of penetration achievable during ...
Muthukumaran Vasudevan   +2 more
doaj   +1 more source

Study of Semi-automatic TIG Welding

open access: yesQUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY, 2003
Manual TIG arc welding method is a difficult operation for skill working, because it is necessary to operate adjusting heat source and adding filler rod in getting on well with molten condition of the base metal. Accordingly, a semi-automatic TIG welding method becomes valid for a settlement to this problem.
HONMA, Shingo, YASUDA, Katsuhiko
openaire   +2 more sources

Development of a Virtual Reality-Based System for Simulating Welding Processes

open access: yesApplied Sciences, 2023
Arc welding processes, such as shielded metal arc welding (SMAW), metal inert gas (MIG), and tungsten inert gas (TIG), play an important role in industrial applications.
Ngoc-Hien Tran   +2 more
doaj   +1 more source

Corrosion behavior of TIG welded AlMg6Mn alloy [PDF]

open access: yesScientific Technical Review, 2016
The influence of TIG welding on the corrosion and mechanical properties of AlMg6Mn was investigated. The as-received hot rolled AlMg6Mn alloy plates (AR) with a thickness of 8 mm were welded by TIG welding with S-AlMg5 as a filler material.
Radović Ljubica   +2 more
doaj  

Activating Flux TIG Welding Technology of 2219 High Strength Aluminum Alloy

open access: yesCailiao gongcheng, 2018
Straight polarity direct current method(DCSP A-TIG) was applied to join 2219 high strength aluminum alloy, and the effects of single-component(AlF3,LiF), three-component (AlF3+30%LiF+10%KF-AlF3) and four-component (AlF3+30%LiF+10%KF-AlF3+10%K2SiF6 ...
LI Hui   +3 more
doaj   +1 more source

Effect of Pre-Post TIG Welding Heat Treatment on Cast NI Superalloy

open access: yesAnnals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology, 2020
The effect of a pre (before) and post (after) heating welding treatment on the microstructure and mechanical properties of the scrap blades made of cast INC738LC superalloy is the main goal of the present investigation. The filler used in TIG welding was
C. Saib   +4 more
doaj   +1 more source

Impact of variable parameters in K-TIG horizontal position welding on penetration state and its recognition based on OCR-SVM model

open access: yesHanjie xuebao
Keyhole tungsten inert gas welding (K-TIG) offers the advantage of single-sided welding with double-sided formation without the need for groove preparation, making it an ideal choice for automated welding processes.
Shizhan ZHAO   +3 more
doaj   +1 more source

Enhancing Welding Productivity and Mitigation of Distortion in Dissimilar Welding of Ferritic-Martensitic Steel and Austenitic Stainless Steel Using Robotic A-TIG Welding Process

open access: yesJournal of Manufacturing and Materials Processing
The P91 martensitic steel and 304L austenitic stainless steels are two mainly used structural steels in power plants. The major problem in conventional multipass tungsten inert gas (TIG) welding of P91/304L steel is high heat input and joint distortion ...
Tushar Sonar   +6 more
doaj   +1 more source

Impact Toughness of Steel WMD After TIG Welding

open access: yesArchives of Metallurgy and Materials, 2017
The material selected for this investigation was low alloy weld metal deposit after TIG welding with various amount of oxygen in weld metal deposit (WMD).
Węgrzyn T.   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy