Results 1 to 10 of about 1,027 (66)

Augmentation of Weld Penetration by Flux Assisted TIG Welding and Its Distinct Variants for Oxygen Free Copper

open access: yesJournal of Materials Research and Technology, 2021
A comparative study to investigate the influences of single component fluxes on the depth-to-width ratio (DWR) of oxygen free copper was carried out with novel variants of tungsten inert gas (TIG) welding namely Activated TIG (A-TIG), Flux Bounded TIG ...
Vishvesh Badheka   +2 more
exaly   +3 more sources

Effect of Fast-Frequency Pulsed Waveforms on the Microstructure and Mechanical Properties of Ti–6Al–4V Alloy Welded by FFP-TIG

open access: yesJournal of Materials Research and Technology, 2022
Ti–6Al–4V alloys have been widely adopted because of their good mechanical properties. TIG welding is a common method for Ti–6Al–4V alloys. However, the high heat input of conventional TIG can lead to a coarsening of grains within Ti–6Al–4V and thus a ...
Zhengchao Xie, Zhenmin Wang, Mengjia Xu
exaly   +3 more sources

Effect of Friction Stir Processing on Mechanical Properties and Heat Transfer of TIG Welded Joint of AA6061 and AA7075

open access: yesDefence Technology, 2021
Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like
Husain Mehdi, R S Mishra
exaly   +3 more sources

FEM Based Thermal and Mechanical Analysis of Comparative Study of TIG and A-TIG Welding on P91 Steel

open access: yesScientific Reports
Present research deals with the thermo-mechanical analysis of the butt joint plate and weld pool characteristics of the bead on plates fabricated using A-TIG and conventional TIG process.
M Vasudevan   +2 more
exaly   +2 more sources

TIG Welding of Ti6Al4V: Effect of Ti6Al4V ELI as Filler Metal [PDF]

open access: yesArchives of Metallurgy and Materials, 2023
Titanium and its alloys have significant uses in the biomedical, chemical, and aerospace industries. In this article, the current and gas flow rates were varied using Taguchi’s experiment design.
P.O. Omoniyi   +5 more
doaj   +1 more source

Assessment of the Corrosion Resistance, Properties and the Structure of Tig Braze Welded Galvanised Steel Sheets [PDF]

open access: yesArchives of Metallurgy and Materials, 2020
The article discusses tests concerning the assessment of the corrosion resistance, properties and the structure of TIG braze welded galvanised steel sheets.
J. Górka
doaj   +1 more source

A Comparison Study of Mechanical Properties between Friction StirWelding and TIG Welded Joints of Aluminum Alloy (Al 6061-T6) [PDF]

open access: yesEngineering and Technology Journal, 2013
In this study two different welding processes have been considered, a conventional tungsten inert gas (TIG) and a relatively new solid state welding known as friction stir welding (FSW).
Muna Khethier Abbass, Hassan Hady Abd
doaj   +1 more source

A Comparative Study of Residual Stress and Mechanical Properties for FSW and TIG Weld on Structural Steel [PDF]

open access: yesArchives of Metallurgy and Materials, 2018
Mechanical properties and residual stresses of friction stir welded and autogenous tungsten inert gas welded structural steel butt welds have been studied.
P.K. Chaurasia   +2 more
doaj   +1 more source

Analysis and Characterization of the Weld Pool and Bead Geometry of Inconel 625 Super-TIG Welds

open access: yesMetals, 2020
The welding market is changing globally, becoming eco-friendly, robotized and automated. The tungsten inert gas welding (TIG) process is indispensable in industries that require high-quality welds with the absence of spatter and fumes.
Jung Hyun Park   +2 more
doaj   +1 more source

Characterization of weld fusion zone for TIG welded P91and P92 steels [PDF]

open access: yesArchives of Metallurgy and Materials, 2018
The welding of nuclear grade P91 and P92 steel plate of thickness 5.2 mm were performed using the autogenous tungsten inert gas (TIG) welding process.
C. Pandey   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy