Results 81 to 90 of about 219 (125)

Chemical and structural evolution of green dispersive Musa paradisiaca composite potential on solid crystal AlMg25PP formation for advance application

Hybrid Advances
This study examines the utilization of plantain peels (Musa paradisiaca) as a strengthening component in aluminum metal matrix composites (AMMCs) for the purpose of cost reduction and the utilization of eco-friendly materials.
Ojo S.I. Fayomi
doaj   +1 more source

The Influence of Sheet Layer Combination Modes on Mechanical Property of Self-Piercing Riveting Joint in Three-Layer Sheets

Applied Mechanics
Unlike previous studies focusing on two-layer structures or single-parameter effects, this work systematically investigates the influence of sheet layer combination modes on the mechanical properties of three-layer AA6063-T6 self-piercing riveting (SPR ...
Zhaohui Hu, Shuai Mo, Yuxuan Wang
doaj   +1 more source

Assessment of Sodum Benzoate Corrosion Inhibitor on AA6063 in Wate

Biosciences Biotechnology Research Asia, 2013
W.B. Wan Nik, O. Sulaiman, S.G. Eng Giap, R. Rosliza   +3 more
openaire   +1 more source

High cycle fatigue of AA6082 and AA6063 aluminum extrusions

, 2020
openaire   +2 more sources

Effect of Punch Surface Grooves on Microformability of AA6063 Backward Microextrusion

Effect of Punch Surface Grooves on Microformability of AA6063 Backward Microextrusion
openaire  

The effect of homogenization practice on the microstructure of AA6063 billets

Journal of Materials Processing Technology, 2004
Abstract It is well established that homogenized billets extrude easier and faster and give better surface finish and higher tensile properties than as-cast billets. Hence, the production of AlMgSi extrusions from DC-cast billets almost always starts with a homogenization cycle which typically consists of a soaking treatment followed by cooling at ...
Yücel Birol
exaly   +3 more sources

Some of the next articles are maybe not open access.

Related searches:

Evaluation of Constitutive Behavior of Aluminum Alloy AA6063-T6

Conference Proceedings of the Society for Experimental Mechanics, 2022
Tiwari Vikrant
exaly   +2 more sources

Characterization of Lateral Friction Surfaced AA6063 Coatings

Volume 3: Advanced Materials: Design, Processing, Characterization, and Applications, 2021
Abstract Friction surfacing is a solid-state metal deposition technique suitable for a wide range of metallic materials. This technique results in coatings on surfaces for joining purposes or surface modification applications such as wear and corrosion performance improvements.
Ebrahim Seidi, Scott F. Miller
openaire   +1 more source

Investigation of the relationship between intergranular corrosion and retrogression and reaging in the AA6063

Materials and Corrosion - Werkstoffe Und Korrosion, 2019
AbstractAA6063 was heat treated with different retrogression temperatures and durations, and the effect of heat treatment conditions on the microstructure, hardness, electrical conductivity, intergranular corrosion (IGC) and electrochemical corrosion behaviours of the AA6063 was determined compared with the T6 condition.
Gokhan Ozer, Alptekin Kisasoz, Ahmet Karaaslan   +2 more
exaly   +4 more sources

Discoloration of Anodized AA6063 Aluminum Alloy

Journal of The Electrochemical Society, 2014
The effect of the anodizing process parameters and the influence of β (Mg2Si) phase on the appearance of the anodized AA6063 aluminum alloy have been investigated. It was found that β (Mg2Si) phase was preferentially oxidized at low anodizing voltages and the selective oxidation of β (Mg2Si) phase resulted in the development of a rough alloy/film ...
Ma, Y., Zhou, X.; id_orcid 0000-0001-9943-3997, Wang, J., Thompson, G. E., Huang, W., Nilsson, J. O., Gustavsson, M., Crispin, A.   +7 more
openaire   +1 more source