Results 21 to 30 of about 22,713 (315)
Abrasive Wear Performance of Coir Fiber Reinforced Polymer Composite [PDF]
, 2023 In the current era, there is a high demand to develop and explore new eco-materials for different engineering applications. Most engineering components are subjected to tri-biological loading conditions during the service.
Yousif, Belal +2 more
core +1 more source
Effect of Experimental Parameters on Wear Response of Thermally Sprayed Carbide Based Coatings [PDF]
Materials Research, 2018 Friction and abrasive wear response of WC-12 Co and Cr3C2-25 NiCr coatings was studied. Abrasive wear experiments were conducted with SiC abrasive particles with varying load and sliding speeds.
Nitesh Vashishtha, Sanjay Sapate
doaj +2 more sources
Wear Resistance of Sintered Composite Hardfacings under Different Abrasive Wear Conditions
Medžiagotyra, 2017 The article focuses on vacuum liquid phase sintered (PM) composite hardfacings and their behaviour under different abrasive wear conditions. Hardfacings studied contained 30 – 50 vol % fine, coarse or multimodal (fine and coarse) hardmetal reinforcement.
Taavi SIMSON +7 more
doaj +1 more source
Grinding and Abrasive Wear [PDF]
Proceedings of the Institution of Mechanical Engineers, 1970 To explore the relationship between grinding and abrasive wear, a range of differing experiments has been performed. These include simple wear tests, dynamometer measurements of grinding forces, simple scratch tests with both idealized indentors and abrasive grits, and the microscopic examination of abrasive wheels and worn surfaces of steel.
T. C. Buttery, J. F. Archard
openaire +1 more source
TEM characterisation of near surface deformation resulting from lubricated sliding wear of aluminium alloy and composites [PDF]
, 2007 Aluminium alloy composites have been extensively investigated for use in tribo-contact applications, however little detailed literature exists on the sub-surface microstructural evolution as a result of lubricated sliding wear.
Rainforth, W.M. +7 more
core +1 more source
Synergistic effects of micro-abrasion–corrosion of UNS S30403, S31603 and S32760 stainless steels [PDF]
, 2007 In this study, the synergistic effects of abrasion and corrosion on UNS S30403, S31603 and S32760 stainless steels have been investigated using a micro-abrasion test rig.
J.O. Bello +5 more
core +1 more source
Journal of Materials Research and Technology, 2022 Tunnel boring machine (TBM) cutter ring material is a type of C–Cr–Mo–V alloy steel which possesses high hardness and wear resistance. To systematically study the effect of tempering temperature on the microstructure, mechanical properties and abrasive ...
Jinzhe Jiang, Yue Liu, Chunming Liu
doaj +1 more source
Analysis of Wear-Resistant Surface with Pangolin Scale Morphology by DEM Simulation
Applied Sciences, 2020 Based on the Discrete Element Method (DEM), an abrasive wear system composed of pangolin scale models and abrasive sand was established. The wear morphology of pangolin scale models under different velocities were simulated by PFC2D®.
Rui Zhang +4 more
doaj +1 more source
Energies, 2021 Since solid particles suspended in the fluid can cause wear in centrifugal pumps, intensive attention has been focused on the numerical prediction for the wear of flow parts in centrifugal pumps.
Cheng Tang +3 more
doaj +1 more source
Archives of Metallurgy and Materials, 2017 This paper presents the results of wear tests of shot-peened and not shot-peened cast steels used in the mining machinery industry, in particular in the construction of chain drums for armoured face conveyors.
Wieczorek A.N.
doaj +1 more source