Results 41 to 50 of about 325,507 (234)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

A multidimensional investigation of the transition from lubricated to abrasive wear

Friction
Abrasive wear is one of the most critical degradation mechanisms in tribological systems, leading to material loss, reduced efficiency, and premature failure of components.
Yulong Li, Johannes Schneider, Christian Greiner   +2 more
doaj   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Effect of Cu and CuP Additions on the Microstructure and Nanoindentation‐Based Fracture Behavior of CoNiAlSi Ferromagnetic Shape Memory Alloys

Advanced Engineering Materials, EarlyView.
Cu and combined Cu–P microalloying refine the microstructure and enhance the nanoindentation‐derived fracture resistance of CoNiAlSi ferromagnetic shape memory alloys without suppressing the martensitic transformation. Comparative SEM, DSC, and nanoindentation results reveal that the CuP‐containing alloy provides the most balanced response, achieving ...
Mehmet Demir
wiley   +1 more source

Self‐Sintering Ionogel Binder for Flexible, Recyclable, and Healable Printed Giant Magnetoresistive Sensors

Advanced Functional Materials, EarlyView.
ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo, Xiaotao Wang, Guannan Mu, Proloy Taran Das, Igor Veremchuk, Conrad Schubert, Aaron D. Cross, Yevhen Zabila, Xuan Peng, Larysa Baraban, Denys Makarov   +10 more
wiley   +1 more source

THE TRIBOLOGICAL BEHAVIOR OF POLYETHYLENE FILLED BY NANOPOWDER OF ALUMINUM OXIDE [PDF]

Journal of the Egyptian Society of Tribology, 2016
The present study investigates the abrasive wear of surfaces subjected to abrasive contaminants. Polyethylene (PE) filled with nanoparticles of aluminum oxide were used as coating for steel specimens.  Their effect on wear of moving surfaces contaminated
A. A. Ezzat, M. O. Mousa, W. Y. Ali
doaj   +1 more source

Advances in Sustainable and Wearable Textile Based Soft Robotics

Advanced Functional Materials, EarlyView.
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas, Marzia Dulal, Sophia K. Novoselov, Victoria K. Novoselov, Kostya S. Novoselov, Shaila Afroj, Nazmul Karim   +6 more
wiley   +1 more source

TEM characterisation of near surface deformation resulting from lubricated sliding wear of aluminium alloy and composites [PDF]

, 2007
Aluminium alloy composites have been extensively investigated for use in tribo-contact applications, however little detailed literature exists on the sub-surface microstructural evolution as a result of lubricated sliding wear.
Rainforth, W.M., Lieblich, M., Walker, J. C., Rainforth, W. M., Ross, I.M., Walker, J.C., Lieblich, Marcela, Ross, I. M.   +7 more
core   +1 more source

Proposal of high frictional and low aggressive abrasive shape (The effect of open angle for friction coefficient on degree of wear in abrasion)

Nihon Kikai Gakkai ronbunshu, 2014
Disc brake is one of the most important auto mobile components and the toughest frictional components. Nowadays, the lightweight disc brake is needed for better fuel-efficient.
Miho SUMIGAMA, Noritsugu UMEHARA, Takayuki TOKOROYAMA, Hiroyuki KOUSAKA   +3 more
doaj   +1 more source

Coordinated Architectural and Chemical Reinforcement in the Crushing Mandible of a Soldier Termite

Advanced Functional Materials, EarlyView.
The crushing mandible of a soldier termite withstands substantial biting loads despite lacking mineral. Its cuticle is partitioned: convex teeth pair hardness and zinc enrichment with aligned chitin fibers for contact durability, while stiffer concave regions between teeth carry bending loads.
Andrew Tran Nguyen, Patryk Wąsik, Juan Fernando Cucuyame Morales, Marie Kate Palau, Adrian Francisco Duran Ornelas, Phani Saketh Dasika, Jin Hee Kim, Radhika Laxminarayana, Eric Hintsala, Greta Chang, Junzhi Liao, Lizhi Sun, Nathan Lord, Atsushi Arakaki, Paul Bardunias, Pablo Zavattieri, David Kisailus   +16 more
wiley   +1 more source