Results 81 to 90 of about 76,140 (267)
Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films
Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee +5 more
wiley +1 more source
Based on the analysis and mathematical models of synchronous electric machines (motor/generator), basing on permanent magnets, presented in this paper, the main importance of alternator AC power sources in the form of starter/generator (for conventional ...
Setlak Lucjan, Kowalik Rafał
doaj +1 more source
A compostable PGS soft surgical robot with interchangeable modules integrates transient Mo tactile and Si thermal sensors for dual feedback. The device preserves its function after clinical‐grade sterilization, demonstrates stable actuation and cardiac tissue grasping with real‐time in vivo pulsatile monitoring, and biodegrades post‐use with soil‐safe,
Minseong Chae +27 more
wiley +1 more source
We present a tissue‐stimulator platform for seamless electrode integration with pancreatic tissue, applying uniform electrical stimulation through optimized design with biohybrid 3D printing. Advantageous effects of electrical stimulation on β‐cell function were observed, including enhanced calcium signaling, islet morphology, and maturation.
Jihwan Kim +7 more
wiley +1 more source
Flexible piezoresistive pressure sensors underpin wearable and soft electronics. This review links sensing physics, including contact resistance modulation, quantum tunneling and percolation, to unified materials/structure design. We highlight composite and graded architectures, interfacial/porous engineering, and microstructured 3D conductive networks
Feng Luo +2 more
wiley +1 more source
Formation of Quasi‐Decoupling Interface on Li‐Metal Anodes in High Donor Electrolyte
Li‐metal anode (LMA) is stabilized by introducing Li2Te2 as an electrolyte additive for Li‐metal batteries. Upon contact with Li, Li2Te2 spontaneously converts to Li2Te, which electronically isolates Li from dimethyl sulfoxide due to its large bandgap and minimal Bader charge transfer.
Hyerim Kim +9 more
wiley +1 more source
Solvent Co‐Intercalation Enabled Ca Storage in MoS2 for Ca‐Ion Batteries
Regulating electrolyte solvation levels enables otherwise non‐intercalatable Ca2+ ions to reversibly co‐intercalate into molybdenum disulfide (MoS2) as ether‐solvated species. The intercalation reversibility is strongly governed by solvent chain length, as demonstrated using diethylene glycol dimethyl ether (G2) and tetraethylene glycol dimethyl ether (
Yudong Luo +10 more
wiley +1 more source
A fluorine‐rich acrylate monomer (PFHEA) was solvent‐free applied to NCM90 and thermally decomposed under Ar to convert residual lithium into LiF and form a pre‐built LiF/fluorinated amorphous carbon (LiF/FC) interphase. The LiF/FC layer suppresses NiO rock‐salt reconstruction and microcrack propagation, lowers interfacial resistance, and improves Li ...
Pangyu Kim +6 more
wiley +1 more source
This work aims to highlight the inadequacy of international standards IEC 60034-2-3 and IEC 60034-30-2 for accurate efficiency, power losses, and efficiency class determination of ac motors fed by multilevel inverters driven with multicarrier pulsewidth ...
Claudio Nevoloso +6 more
doaj +1 more source
Wafer‐scale two‐dimensioanl In2Se3 oxidized into InOx on sodium‐embedded beta‐alumina enables multifunctional reconfigurable electronics. Sodium ions accumulate within distinct spatial distribution under drain‐controlle and gate‐controlled operation. Drain‐control operation gives controllability of ultraviolet‐driven optoelectronic synaptic conductance
Jinhong Min +13 more
wiley +1 more source

