Results 161 to 170 of about 13,673 (273)

Analysis of Tyre Pyrolysis Oil as Potential Diesel Fuel Blend with Focus on Swelling Behaviour of Nitrile-Butadiene Rubber. [PDF]

Polymers (Basel)
Seitz S, Förster T, Eibl S.
europepmc   +1 more source

From Waste to Value: Conversion of Calcium Sulfate to Vaterite via Carbon Capture and Storage

Advanced Functional Materials, EarlyView.
This study introduces a new concept for carbon management that relies on the carbonation of industrial gypsum waste and yields phase‐pure vaterite at ambient conditions without any additives. The obtained vaterite is further shown to be a reactive material that develops compressive strength in aqueous suspensions like conventional cements.
Carlos Pimentel, German Montes‐Hernández, Pablo Almarza‐Cifuentes, Matthias Kellermeier, Alexander E.S. Van Driessche   +4 more
wiley   +1 more source

Sub-THz Characterization of Technical Surfaces for Particle Accelerator Vacuum Chambers. [PDF]

Sensors (Basel)
Passarelli A, Masullo MR, Mazaheri Z, Andreone A.   +3 more
europepmc   +1 more source

Laser‐Induced Microfabrication of Carbon Nanostructure: Processing Mechanism and Application for Next‐Generation Battery Technology

Advanced Functional Materials, EarlyView.
The article reviews laser‐processed carbons from various precursors, processing mechanism and their application in advanced batteries. The laser process is chemical free, fast, and scalable, enabling improved battery performance and stability for Li, Na, and Zn battery technologies.
Sujit Deshmukh, Shaista Nouseen, Martin Pumera   +2 more
wiley   +1 more source

Colloidal Crack Sintering Lithography for Light‐Induced Patterning of Particle Assemblies

Advanced Functional Materials, EarlyView.
Colloidal crack sintering lithography (CCSL) is a microfabrication technique that uses light‐induced photothermal heating to trigger sintering and controlled cracking in polymer colloidal assemblies. Local structural changes generate microchannels and patterns, enabling direct writing of diverse topographic motifs.
Marius Schoettle, Ariane V. Mader, Willem L. Noorduin   +2 more
wiley   +1 more source

Button-Type Beam Position Monitor Development for Fourth-Generation Synchrotron Light Sources: Numerical Modeling and Test Bench Measurements. [PDF]

Sensors (Basel)
Cleva S, Bassanese S, Comisso M, El Ajjouri M, Sergo R, Morello C, Passarelli A.   +6 more
europepmc   +1 more source

Throbbing Beam Transverse Resistive Instabilities in Circular Accelerators and Storage Rings [PDF]

, 1967
Lee, M. J., Mills, F. E., Morton, P. L.
openaire   +3 more sources

Spatiotemporal Plasma–Mediated Laser Fabrication of Ultrahigh‐Aspect‐Ratio Nanochannel Arrays for Vertical Perovskite Nanowire Semiconductor Devices

Advanced Functional Materials, EarlyView.
A spatiotemporal plasma–mediated laser processing approach is developed to fabricate ultrahigh–aspect ratio nanochannel arrays and corresponding perovskite nanowire arrays within transparent materials for optoelectronics devices. The laser‐fabricated nanochannels serve as templates for controlled perovskite infiltration and crystallization, enabling ...
Taijin Wang, Lingfeng Wang, Feng Liu, Gary J. Cheng   +3 more
wiley   +1 more source

KOH-activated micrometer-thick amorphous carbon nanofoam as a binder-free supercapacitor electrode with high-rate performance.

Chem Commun (Camb)
Ghosh S, Zhang Y, Pagani G, Suriano R, Agozzino M, Jastrzębska A, Casari CS.   +6 more
europepmc   +1 more source

High-performance and recyclable epoxy resins based on fully bio-based hardeners containing Schiff base structures. [PDF]

R Soc Open Sci
Zhang R, Zhong J, Wu G, Xu K, Xu X, Cui X, Xu B, Li X.   +7 more
europepmc   +1 more source