Results 41 to 50 of about 667 (249)
Frontiers in Materials, 2020 AA1050/AA7050 multilayered composite sheets with a proportion of 1:1 were produced by Accumulative Roll Bonding (ARB) and Asymmetric Accumulative Roll-Bonding (AARB), using up to 8 cycles and intermediate annealing treatments at 500°C.
D. C. C. Magalhães +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 Tougher and stronger alloys are desired for structural applications, but the strength-ductility trade-off limits it. In order to overcome this issue, heterogeneous structures can be developed in high-strength materials to restore an acceptable ductility ...
Danielle Cristina Camilo Magalhães +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Metals, 2020 In this work, accumulative pack-roll bonding successfully manufactured the Ni/Ti/Nb multilayer composite. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by ...
Nan Ye, Xueping Ren, Juhua Liang
doaj +1 more source
Advanced Functional Materials, EarlyView.An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone +11 more
wiley +1 more source
Particle Based Alloying by Accumulative Roll Bonding in the System Al-Cu
Metals, 2011 The formation of alloys by particle reinforcement during accumulative roll bonding (ARB), and subsequent annealing, is introduced on the basis of the binary alloy system Al-Cu, where strength and electrical conductivity are examined in different ...
Mathias Göken +3 more
doaj +1 more source
Enhancement of mechanical properties for Mg-9Li-1Zn alloy by accumulative roll bonding
Materials Research Express, 2020 The microstructures and mechanical properties of LZ91 alloys by accumulative roll bonding (ARB) were firstly investigated. The results show that the cycle numbers of ARB process and preheating temperatures before ARB process have an impact on the ...
Akhmad Saufan +2 more
doaj +1 more source
Advances in Sustainable and Wearable Textile Based Soft Robotics
Advanced Functional Materials, EarlyView.This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas +6 more
wiley +1 more source
Electrospun Wood‐Derived Biopolymers as Electrodes in Electrochemical Energy Storage Technologies
Advanced Functional Materials, EarlyView.Electrospinning transforms wood‐derived cellulose and lignin into architecturally defined, binder‐free carbon electrodes with tuneable porosity and functionality. This review shows how fibre design enables decoupled charge and mass transport, enhancing performance across battery systems, while identifying key challenges in spinnability, scalability ...
Michael W. Thielke +3 more
wiley +1 more source
Metallurgical and Materials Transactions A, 2014 The bond strength in bimetallic materials is an important material characteristic. In this study, 0.1-mm thick bimetallic foils (AA1050/AA6061) were produced using one pass of accumulative roll bonding followed by three passes of asymmetric rolling (AR).
Yu, Hailiang +3 more
openaire +3 more sources