Tribological behaviour of acrylonitrile-butadiene rubber under thermal oxidation ageing
Polymer Testing, 2021 Acrylonitrile–butadiene rubber (NBR) is an important tribological material that is often used in dynamic sealing pairs (as rubber/metal seal-pairs), but often degrades prematurely because of thermal oxidation ageing.
Bo Li +6 more
doaj +2 more sources
Effect of Functional Fillers on Tribological Characteristics of Acrylonitrile Butadiene Rubber after High-Pressure Hydrogen Exposures. [PDF]
Polymers (Basel), 2022 In a high-pressure hydrogen environment, the sealing rubber material is swelled by hydrogen, and the mechanical and tribological properties are reduced, causing various problems in the sealing performance.
Choi BL, Jung JK, Baek UB, Choi BH.
europepmc +2 more sources
Effect of a Natural Processing Aid on the Properties of Acrylonitrile-Butadiene Rubber: Study on Soybean Oil Fatty Acid from Seed Crop. [PDF]
Polymers (Basel), 2021 For the industrial production of rubber, one of the key ingredients is a processing aid. It not only facilitates the processability but also tunes the final properties of the resultant rubber.
Nun-Anan P, Hayichelaeh C, Boonkerd K.
europepmc +2 more sources
On the Influence of Viscoelastic Modeling in Fluid Flow Simulations of Gum Acrylonitrile Butadiene Rubber. [PDF]
Polymers (Basel), 2021 Computational fluid dynamics (CFD) simulation is an important tool as it enables engineers to study different design options without a time-consuming experimental workload.
Stieger S +10 more
europepmc +2 more sources
Enhanced compatibility, morphology, rheological and mechanical properties of carboxylated acrylonitrile butadiene rubber/chloroprene rubber/graphene nanocomposites: effect of compatibilizer and graphene content. [PDF]
RSC Adv, 2020 Elastomeric nanocomposites were prepared from carboxylated acrylonitrile butadiene rubber/chloroprene rubber (XNBR/CR), graphene and a glycidyl methacrylate (GMA)-grafted XNBR (XNBR-g-GMA) compatibilizer by using a two-roll mill.
Azizli MJ +4 more
europepmc +2 more sources
Utilization of Leather Waste Fibers in Polymer Matrix Composites Based on Acrylonitrile-Butadiene Rubber. [PDF]
Polymers (Basel), 2020 In this study, we present the fabrication of nitrile butadiene rubber/waste leather fiber (NBR/WLF) composites with different weight percentages of WLF and NBR (0/100, 20/80, 30/70, 40/60, 50/50, 60/40 wt/wt).
Hang LT +6 more
europepmc +2 more sources
Gas Barrier, Rheological and Mechanical Properties of Immiscible Natural Rubber/Acrylonitrile Butadiene Rubber/Organoclay (NR/NBR/Organoclay) Blend Nanocomposites. [PDF]
Materials (Basel), 2020 In this paper, gas permeability studies were performed on materials based on natural rubber/acrylonitrile butadiene rubber blends and nanoclay incorporated blend systems. The properties of natural rubber (NR)/nitrile rubber (NBR)/nanoclay nanocomposites,
Maria HJ +9 more
europepmc +2 more sources
Clean Technologies and Environmental Policy, 2022 Red brick waste (RBW) powder was used as a reinforcing filler for acrylonitrile butadiene rubber (NBR) for preparing eco-friendly composites. The main constituent of this waste is silica which is considered to be one of the traditional fillers used in ...
E. S. Shafik +2 more
semanticscholar +1 more source
eXPRESS Polymer Letters, 2023 Increasing demand for durable rubber and rapid advancement in the automotive sector has made oil-resistant rubber an increasingly important material. Among them, nitrile rubber (NBR) is the most iconic due to its extraordinary oil resistance contributed ...
Zhen Hern Boon +2 more
doaj +1 more source
Effect of Rubber Content in Acrylonitrile–Butadiene–Styrene and Additional Rubber on The Polymer Blends of Polycarbonate and Acrylonitrile–Butadiene–Styrene [PDF]
Polymer Journal, 1994 Higher ABS rubber content in the polycarbonate (PC)/acrynitrile–butadiene–styrene (ABS) blend resulted in toughness improvement in terms of tensile, Izod impact and strain energy release rate at a cost of higher melt viscosity. The extra-added core-shell rubber particles with poly(methyl methacrylate) (PMMA) or acrylonitrile–styrene (SAN) outer shell ...
Jiann-Shing Wu +2 more
openaire +1 more source