Results 211 to 220 of about 27,777 (261)

Deformation modes and fatigue behavior in styrene‐acrylonitrile and acrylonitrile‐butadiene‐styrene copolymers

Polymer Engineering & Science, 1984
AbstractThe performance of styrene‐acrylonitrile copolymers under alternating stresses has been examined. Information has been obtained concerning the influence of acrylonitrile content and of molecular weight on thermal effects due to hysteresis, on cyclic lifetime to craze initiation, on average cycles to fracture, and on fatigue fracture surface ...
J. A. Sauer, C. C. Chen
openaire   +1 more source

Dielectric Relaxation Spectroscopy of a Poly (Acrylonitrile-Butadiene-Styrene)/Styrene-Acrylonitrile Polymer Blend

Journal of the Korean Physical Society, 2011
characterized by a high dielectric constant ( 0 ) at low frequency and high temperature. In addition, the dielectric loss (tan ) showed a frequency dependent relaxational peak for all samples. Moreover, the temperature dependence of the AC conductivity was investigated for all samples, and the values of the activation energy were estimated.
T. Fahmy, M. T. Ahmed
openaire   +1 more source

Comparison of the fast fracture properties of acrylonitrile-butadiene-styrene and styrene-acrylonitrile

Journal of Materials Science, 1996
The resistance of polymers, with toughening agents, to fast crack propagation under steady load conditions was studied, and the fracture resistance of acrylonitrile-butadiene-styrene (ABS) was compared with styrene-acrylonitrile (SAN). Small laboratory specimens were used which could be precisely loaded and allowed to stress relax before being ...
J. C. Graham, J. P. Dear
openaire   +1 more source

Acrylonitrile-butadiene-styrene (ABS) - a review

Composites, 1973
Abstract One of the most successful polymer composites with an unequalled variety of forms and range of ...
openaire   +1 more source

Fracture analysis of acrylonitrile‐butadiene‐styrene resins

Polymer Engineering & Science, 1982
AbstractThe fracture properties of three grades of acrylonitrile‐buta‐diene‐styrene(ABS) were evaluated and compared. In preliminary studies, J1c (J integral) results obtained using the Begley and Landes procedure for single‐edge‐notched tension specimens and compact tension specimens were compared to establish the validity of the J1c criterion.
N. S. Sridharan, L. J. Broutman
openaire   +1 more source

Atomically dispersed iridium on MgO(111) nanosheets catalyses benzene–ethylene coupling towards styrene

Nature Catalysis, 2021
Pengxin Liu, Xing Huang, Deni Mance
exaly  

Study properties of blends between acrylonitrile-butadiene rubber and acrylonitrile-butadiene-styrene or poly(styrene-co-acrylonitrile)

In this study, the influences of alcohol and gasoline on mechanical and physical properties of blends between acrylonitrile-butadiene rubber (NBR) with acrylonitrile-butadiene-styrene (ABS) orpoly(styrene-co-acrylonitrile) (SAN), and hydrogenated acrylonitrile-butadiene rubber (HNBR) were investigated.
openaire   +1 more source

Propane dehydrogenation: catalyst development, new chemistry, and emerging technologies

Chemical Society Reviews, 2021
Sai Chen, Guodong Sun, Chunlei Pei
exaly  

Acrylonitrile Butadiene Styrene

1990
Tony Whelan, John Goff
openaire   +1 more source

Investigation into the catalytic roles of oxygen vacancies during gaseous styrene degradation process via CeO2 catalysts with four different morphologies

Applied Catalysis B: Environmental, 2022
Yongming Luo
exaly