Results 131 to 140 of about 1,410,743 (209)

Calligraphy‐Brush‐Fabricated Xuan Paper for Sustainable Direct‐Current Triboelectric Nanogenerators in Human‐Motion Energy Harvesting and Biomedical Sensing

open access: yesEcoMat, Volume 8, Issue 10, October 2026.
A sustainable direct‐current triboelectric nanogenerator (DC‐TENG) was fabricated using brush‐coated Xuan paper and a water‐processable PEDOT:PSS/PVA/pullulan conductive network. The cellulose‐based composite enables intrinsic rectifier‐free DC output through interfacial charge transport at the Al/conductive interface, demonstrating an eco‐friendly ...
Min‐Hsuan Lee
wiley   +1 more source

DEET‐cyclodextrin inclusion complexes for mosquito and tick repellency: Extended repellency time and no zebrafish embryotoxicity

open access: yesPest Management Science, Volume 82, Issue 10, Page 9653-9665, October 2026.
Hydroxypropyl‐β‐cyclodextrin (HPβCD)–N,N‐diethyl‐meta‐toluamide (DEET) complex extended tick repellency to 168 h. Full protection against Aedes aegypti for 7 h with HPβCD‐DEET. HPβCD reduced DEET release and skin retention significantly. No embryotoxicity observed below 325 mg L−1 in zebrafish model.
Gessyka Rayana Silva Pereira   +10 more
wiley   +1 more source

Postcranial anatomy of the Miocene hippopotamoids of Toros‐Menalla, Chad

open access: yesJournal of Anatomy, Volume 249, Issue 4, Page 924-949, October 2026.
We establish a framework for the identification of postcranial remains in hippopotamoids by describing and comparing for the first time two late Miocene hippopotamoids from Toros‐Menalla, Chad (Hexaprotodon garyam, an early hippopotamid, and Libycosaurus bahri, the last African anthracothere) with the common hippopotamus.
Lorenzo Scribano   +4 more
wiley   +1 more source

In-Situ Monitoring and Control of Additive Friction Stir Deposition. [PDF]

open access: yesMaterials (Basel)
Yasa E   +5 more
europepmc   +1 more source

AI‐driven discovery of feasible 3D printing configurations for metal alloys

open access: yesAI Magazine, Volume 47, Issue 3, Fall 2026.
Abstract Configuring additive manufacturing (AM) processes for metal alloys is challenging because printed output quality depends on complex interactions among process parameters such as laser power, scan speed, and feed rate. Conventional trial‐and‐error approaches are inefficient because experiments are costly and the process parameter space is ...
Azza Fadhel   +5 more
wiley   +1 more source

Recent Advances in Additive Friction Stir Deposition: A Critical Review. [PDF]

open access: yesMaterials (Basel)
Dong X   +6 more
europepmc   +1 more source

Snap‐Through–Driven Liquid Crystal Elastomers for High‐Power Remote Microneedle Actuation Toward Smart Livestock Systems

open access: yesAdvanced Functional Materials, Volume 36, Issue 72, 7 September 2026.
A magnetically assisted snap‐through liquid crystal elastomer transforms photochemical deformation into a high‐power mechanical impulse, enabling remote microneedle actuation and highlighting its potential for future smart livestock intervention systems.
Chae Won Lee   +3 more
wiley   +1 more source

Effect of Additive Friction Stir Deposition Processing on the Microstructure and Mechanical Properties of 1045 Steel. [PDF]

open access: yesMaterials (Basel)
Lei W   +9 more
europepmc   +1 more source

Cellular Responses to Mechanical Cues Across Scales: From Fundamental Insights to Translational Potential

open access: yesAdvanced Healthcare Materials, Volume 15, Issue 35, 18 September 2026.
This review examines how cellular behavior is regulated by mechanical cues transmitted through soft biomaterials, from single‐cell mechanosensing to tissue‐level adaptation. It highlights why physiological relevance, rather than model complexity alone, is critical for translational mechanobiology and introduces a scoring framework linking material ...
Mathias Polz   +9 more
wiley   +1 more source

Home - About - Disclaimer - Privacy