Results 151 to 160 of about 451,106 (279)

Bulk Phase Proportion Governs the Wear Performance of PEO Coatings Grown on Biomedical Ti-6Al-4V Alloy. [PDF]

Materials (Basel)
Neto JRF, Torrento JEM, da Silva CE, Quadros FF, Grandini CR, Tsipas SA, Correa DRN.   +6 more
europepmc   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Comparison of Gentleness and Reapplication Between Two Pulse Oximetry Probes in Healthy Adults in a Laboratory Setting. [PDF]

Med Devices (Auckl)
Grove G, Houser T, Dove J, Moody D.
europepmc   +1 more source

3D‐Printed Corneal Substitutes: Materials, Fabrication, and Preclinical Progress

Advanced Materials Technologies, EarlyView.
Successful clinical translation of 3D‐printed corneal substitutes relies on the interplay between the bioink properties, cellular component, and the fabrication process. These factors influence the critical properties of the construct, including optical transparency, mechanical stability, suture retention, that ultimately govern long‐term stromal ...
Shadi Moshayedi, Ashley Vazquez, Alexander J. Choi, Dimitrios Karamichos, Jayoung Kim   +4 more
wiley   +1 more source

Minimally Invasive Rehabilitation of a Worn Dentition in a Young Patient: A Case Report. [PDF]

Case Rep Dent
Mancini L, Liguori MG, Fischli T, Ioannidis A.   +3 more
europepmc   +1 more source

Advanced Manufacturing of Composite‐Based Systems for Energy Applications

Advanced Materials Technologies, EarlyView.
Advanced manufacturing enables the integration of polymers, ceramics, metal oxides, and composites into architected microstructures with tailored transport pathways. By coupling material selection, manufacturing strategy, and structural design, multifunctional energy systems can simultaneously improve electrochemical performance, thermal management ...
Sri Vaishnavi Thummalapalli, Dhanush Patil, Libin Yang, M. Taylor Sobczak, Anshul Kulkarni, Xiao Sun, Arunachalam Ramanathan, Tiantian Li, Ramaraja P. Ramasamy, Jason J. Locklin, Yanyu Chen, Xianqiao Wang, Arunachala Mada Kannan, Kenan Song   +13 more
wiley   +1 more source

Friction and Wear Behaviors of PEEK/h-BN/SCF Composites Under Dry and Starved Oil Lubrications. [PDF]

Materials (Basel)
Tong Z, Song X, Lei W, Zhang Y, Li J, Zhao L.   +5 more
europepmc   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

Formation and compaction of sub-10 nm transfer films in metal-ceramic fretting. [PDF]

Beilstein J Nanotechnol
Çiftçi T, Şahin O, Roch T, Weber B.
europepmc   +1 more source

3D‐Printed Dual‐Doped Ag2Se‐Based Thermoelectric Films With Enhanced Thermal Stability

Advanced Materials Technologies, EarlyView.
Sb–Se dual doping enhances the thermal stability of Ag2Se‐based thermoelectric systems. The compositionally tuned nano‐ink is printed into flexible films by direct ink writing (DIW), retaining improved thermoelectric properties after annealing up to 400°C.
Ahasun Habib Hridoy, Nishat Paul, Naimul Arefin, Axel Lopez, Peiran Wei, Brandon Dumars, Yan Chen, Mortaza Saeidi, Minxiang Zeng   +8 more
wiley   +1 more source