Results 151 to 160 of about 15,757 (248)
Field Performance Of Concrete Admixtures
310563This project investigated compatibility problems involving two concrete admixtures from W.R. Grace Products and Dacotah portland cement. The problems experienced by the South Dakota Department of Transportation (SDDOT) were described as rapid slump
Hansen, M.R., Flottmeyer, Brenda L.
core
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Mineral admixtures for concrete
, 2019 U ovom završnom radu obrađena je tema mineralnih dodataka betonu. Dodaci betonu su tvari koje predstavljaju moguća rješenja za poboljšanje svojstava svježeg i očvrsnulog betona. Naime, u današnje je vrijeme sve veći naglasak na očuvanje i brigu o okolišu.
Grigić, Lara
core
Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses
Advanced Engineering Materials, EarlyView.Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk +4 more
wiley +1 more source
Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System
Advanced Engineering Materials, EarlyView.Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner +7 more
wiley +1 more source