Results 121 to 130 of about 4,549,568 (211)

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

open access: yesAdvanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees   +6 more
wiley   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

open access: yesAdvanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak   +4 more
wiley   +1 more source

Visual detection of Ca2+ based on aggregation-induced emission of Au(I)-Cys complexes with superb selectivity

open access: yes, 2015
A label-free optical probe was developed for Ca2+ detection based on the    aggregation-induced emission property of Au(I)-thiolate complexes.
Pei, RJ (裴仁军)   +6 more
core  

Focus on aggregation-induced emission

open access: yesCell Reports Physical Science, 2022
Dong Wang, Ben Zhong Tang, Yan Li
doaj   +1 more source

How does aggregation‐induced emission aggregate interdisciplinary research?

open access: yesAggregate
It is a matter of debate whether the discipline independence in discipline formation narrows its interdisciplinarity. It is also less well understood how disruptive works emerge in investigative practice rather than a theory‐driven approach.
Jing Zhu, Xuefeng Jiang
doaj   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

open access: yesAdvanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery

open access: yesAdvanced Engineering Materials, EarlyView.
We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin   +16 more
wiley   +1 more source

Kinetic network models to elucidate aggregation dynamics of aggregation‐induced emission systems

open access: yesAggregate
Aggregation‐induced emission (AIE) is a phenomenon where a molecule that is weakly or non‐luminescent in a diluted solution becomes highly emissive when aggregated.
Zige Liu   +4 more
doaj   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

open access: yesAdvanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy