Results 81 to 90 of about 72,019 (264)
Effect of Fluidized Bed Particle Size on Heat Transfer Coefficient at Different Operating Conditions
Tikrit Journal of Engineering Sciences, 2018 The aim of this study is to investigate the effect of gas flow velocity, size of sand particles, and the distance between tubes immersed in a fluidized bed on heat transfer coefficient. Experimental tests were conducted on a bundle of copper tubes of (12.
Ehsan Fadhil Abbas, Sarah Burhan Izat
doaj +1 more source
Occupational health review, 1965 Factors that affect thermal sensations of comfort including the role of radiative energy exchanges between various surfaces in the room are discussed. It is shown that limitations in the uniformity of conditions influencing comfort may be imposed by the nature of the room and its occupancy, by the system capability and controllability, and by the air ...
openaire +2 more sources
β‐Catenin/c‐Myc Axis Modulates Autophagy Response to Different Ammonia Concentrations
Advanced Biology, Volume 9, Issue 3, March 2025.Ammonia, detoxified by the liver into urea and glutamine, impacts autophagy differently at varying levels. Low ammonia activates autophagy via c‐Myc and β‐catenin, while high levels suppress it. Using Huh7 cells and Spf‐ash mice, c‐Myc's role in cytoprotective autophagy is revealed, offering insights into hyperammonemia and potential therapeutic ...
S. Sergio +11 more
wiley +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this review, the current state of light‐assisted 3D printing as it pertains to engineering musculoskeletal tissues including bone, cartilage, skeletal muscle, tendon, and ligaments is summarized. Common printing techniques, photoreactive materials, and study design choices are compiled and reviewed.
Meagan Morgan, Bin Zhang, Roger Narayan
wiley +1 more source
EnergiesThis study analyzes several design cases to identify the optimum geometric structure of the offset fin, determined by two design factors: the number of fins in the flow direction and the number of fins in the vertical direction.
Sung-Hoon Seol +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
EnergiesThis study investigates the energy performance of anaerobic digesters in a municipal wastewater treatment plant by integrating empirical data from two tanks located at different distances from the heat source with simulation results.
Ewelina Stefanowicz +2 more
doaj +1 more source