Results 171 to 180 of about 5,648,704 (342)
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Do air-gaps behind soft body armour affect protection?
Journal of the Royal Army Medical Corps, 2017 L. Tilsley +3 more
semanticscholar +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source