Results 21 to 30 of about 34,678 (228)
Journal of Materials Research and Technology, 2020 In this study, 1.5-mm-thickness ferritic AISI 430 and austenitic AISI 304 stainless steel are resistance spot-welded by combining 304/304, 304/430 and 430/430.
Yu Zhang +4 more
doaj +1 more source
Low cycle fatigue life improvement of AISI 304 by initial and intermittent wire brush hammering [PDF]
, 2013 The effects of hammering by wire brush as a method of improving low cycle fatigue life of highly ductile austenitic stainless steel AISI 304 have been investigated through an experimental study combining imposed strain fatigue tests and assessment of ...
BRAHAM, Chedly +4 more
core +3 more sources
Investigation of the Microstructure and Wear Properties of AISI 304 Steel Friction Weldments
Zanco Journal of Pure and Applied Sciences, 2020 In this study, a rotary friction welding technique was used to join austenitic stainless-steel grade AISI 304. The effect of different forging pressure (192.4, 240.5, 288.6 and 384.8 MPa) on wear resistance of AISI 304 were examined using a modified pin
Jwan Kh. Hamad +2 more
doaj +3 more sources
Авіаційно-космічна техніка та технологія, 2020 Extensive investigations of the corrosion resistance of austenitic chromium-nickel steels (with stable and unstable austenite) do not reveal the full nature of the phenomena studied. By the magnetometric method, using the specific magnetic susceptibility
Геннадий Валентинович Снежной +1 more
doaj +1 more source
On the kinetics of oxidation of austenitic stainless steels AISI 304 and incoloy 800H [PDF]
, 1987 The interaction of oxygen with clean surfaces of stainless steels has been studied by spectroscopic ellipsometry and AES. The reaction involves chemisorption and dissolution of oxygen into the surface of the metal via a place-exchange mechanism.
Gellings, P.J. +2 more
core +3 more sources
Damage Mechanisms in AISI 304 Borided Steel: Scratch and Daimler-Benz Adhesion Tests [PDF]
Materials Research, 2015 In this study, damage mechanisms in the FeB/Fe2B coatings formed on the surface of AISI 304 steel are determined by adhesion tests. First, the boriding of the AISI 304 steel was carried out through the powder-pack method at 1223 K in the range from 2-10 ...
German Anibal Rodríguez-Castro +6 more
doaj +1 more source
Rekayasa Mesin, 2023 Welding is often used in industry as a joining technique, one of which is Micro Resistance Spot Welding (MRSW). MRSW was carried out to know the maximum load and shear stress produced on separate worksheets using AISI 304 and aluminum alloys and then ...
Agus Sifa +2 more
doaj +1 more source
On the oxide formation on stainless steels AISI 304 and incoloy 800H investigated with XPS [PDF]
, 1987 The influence of cold work on the initially formed oxide layer on the stainless steels AISI 304 and Incology 800H has been studied by XPS. Oxidations were performed at pressures of 10-6-10-4 Pa and temperatures of 300–800 K.
Gellings, P.J. +3 more
core +2 more sources
Comparison of the corrosion behavior of AISI 304, AISI 316L and duplex steel in chloride solution
Zaštita Materijala, 2018 The corrosion behavior of stainless steels (AISI 304, AISI 316L and duplex steel) in NaCl solution was investigated using open circuit potential measurements, cyclic polarization and linear sweep voltammetry measurements.
Senka Gudić +2 more
doaj +1 more source
Formability Prediction of Laser-Welded Stainless Steel AISI 304 and AISI 430
Metals, 2021 The effect of laser welding on the mechanical properties and the prediction of formability for austenitic stainless steel AISI 304 and ferritic steel AISI 430 when welded by a YLS-5000 fiber laser, were studied in the paper.
Emil Evin, Miroslav Tomáš
doaj +1 more source