Corrosion Behavior of Sensitized AISI 304 Stainless Steel in Acid Chloride Solution. [PDF]
Materials (Basel), 2022 Corrosion resistance of sensitized austenitic stainless steel (SS) in chloride environments is currently the subject of numerous studies. Most of them are focused on neutral chloride solutions at room temperature and the experiments are carried out on ...
Zatkalíková V +3 more
europepmc +2 more sources
Corrosion Behavior of AISI 304 Stainless Steel Reinforcements in SCBA-SF Ternary Ecological Concrete Exposed to MgSO4. [PDF]
Materials (Basel), 2020 In this study, ternary ecological concrete (TEC) mixtures were produced with partial substitution of the ordinary Portland cement (OPC) by 10%, 20%, and 30% of sugar cane bagasse ash (SCBA) and silica fume (SF); a control mixture (100% OPC) was prepared ...
Ariza-Figueroa HA +9 more
europepmc +2 more sources
Hardness, grainsize and porosity formation prediction on the Laser Metal Deposition of AISI 304 stainless steel [PDF]
International journal of machine tools & manufacture, 2018 The presented numerical model solves the heat and mass transfer equations in the Laser Metal Deposition process and based on the evolution of the thermal field predicts the grainsize, the resulting hardness and evaluates the pores formation probability ...
Alberdi, Amaia +4 more
core +4 more sources
Journal of Materials Research and Technology, 2020 In this study, 1.5-mm-thickness ferritic AISI 430 and austenitic AISI 304 stainless steel are resistance spot-welded by combining 304/304, 304/430 and 430/430.
Yu Zhang +4 more
doaj +2 more sources
High temperature oxidation behavior of AISI 304 and AISI 430 stainless steels [PDF]
Materials Research, 2006 The oxidation behavior of AISI 304 and AISI 430 stainless steels was investigated from 1100 °C up to 1200 °C. Mössbauer spectroscopy and x ray diffraction were used to access the phase composition of the formed scales. The main crystalline phases
Carlos Eduardo Reis de Carvalho +3 more
doaj +4 more sources
OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD [PDF]
Journal of Engineering Science and Technology, 2010 The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS). This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless ...
D. PHILIP SELVARAJ, P. CHANDRAMOHAN
doaj +2 more sources
Effect of Built-Up Edge Formation during Stable State of Wear in AISI 304 Stainless Steel on Machining Performance and Surface Integrity of the Machined Part. [PDF]
Materials (Basel), 2017 During machining of stainless steels at low cutting -speeds, workpiece material tends to adhere to the cutting tool at the tool–chip interface, forming built-up edge (BUE).
Ahmed YS +4 more
europepmc +2 more sources
Journal of Materials Research and Technology, 2019 It is clear that the corrosion resistance of carbon steels decreases as cold working amount increases, but for austenitic stainless steels, the relation between cold-working and corrosion performance is not clear. The electrochemical behavior of AISI 304
Gleidys Monrrabal +4 more
doaj +2 more sources
Metals, 2020 Deoxidized oxygen free copper C12200, 1 mm in thickness, was welded to 1-mm thick AISI 304 stainless steel with disk laser. The butt-welded joints were produced with different welding parameters.
Miroslav Sahul +5 more
doaj +2 more sources
Experimental and numerical study of dissimilar fiber laser welding of martensitic AISI 1060 carbon steel with different configuration with austenitic 304 and ferritic 420 stainless steel [PDF]
HeliyonWelding with fiber laser for two distinct stainless steel types was performed to join with the martensitic carbon steel (AISI 1060) in order to assess the effect of laser welding operating parameters for two dissimilar materials on the weld ...
Akbar Zarei +3 more
doaj +2 more sources