Results 11 to 20 of about 30,978 (228)
Journal of Materials Research and Technology, 2020 In this study, 1.5-mm-thickness ferritic AISI 430 and austenitic AISI 304 stainless steel are resistance spot-welded by combining 304/304, 304/430 and 430/430.
Yu Zhang +4 more
doaj +2 more sources
Corrosion Behavior of Sensitized AISI 304 Stainless Steel in Acid Chloride Solution. [PDF]
Materials (Basel), 2022 Corrosion resistance of sensitized austenitic stainless steel (SS) in chloride environments is currently the subject of numerous studies. Most of them are focused on neutral chloride solutions at room temperature and the experiments are carried out on ...
Zatkalíková V +3 more
europepmc +2 more sources
Journal of Materials Research and Technology, 2019 It is clear that the corrosion resistance of carbon steels decreases as cold working amount increases, but for austenitic stainless steels, the relation between cold-working and corrosion performance is not clear. The electrochemical behavior of AISI 304
Gleidys Monrrabal +4 more
doaj +2 more sources
Metals, 2020 Deoxidized oxygen free copper C12200, 1 mm in thickness, was welded to 1-mm thick AISI 304 stainless steel with disk laser. The butt-welded joints were produced with different welding parameters.
Miroslav Sahul +5 more
doaj +2 more sources
AISI 304 stainless steel milling process state diagnosing
MATEC Web of ConferencesThe article presents the results of works on the analysis of using cutting forces and torque to determine AISI 304 stainless steel milling process state. The research and analyzes were carried out for the determine tool state and the process state itself.
Polasik Robert +2 more
openaire +3 more sources
Corrosion Behavior of AISI 304 Stainless Steel Reinforcements in SCBA-SF Ternary Ecological Concrete Exposed to MgSO4. [PDF]
Materials (Basel), 2020 In this study, ternary ecological concrete (TEC) mixtures were produced with partial substitution of the ordinary Portland cement (OPC) by 10%, 20%, and 30% of sugar cane bagasse ash (SCBA) and silica fume (SF); a control mixture (100% OPC) was prepared ...
Ariza-Figueroa HA +9 more
europepmc +2 more sources
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels [PDF]
Materials, 2020 A dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements.
Krzysztof Pańcikiewicz +3 more
openaire +2 more sources
Metals, 2023 Machining of AISI 304 austenitic stainless steel is considered to be difficult due to its structural aspects and low thermal conductivity, which leads to increased temperatures during machining.
Rüstem Binali +3 more
semanticscholar +1 more source
Metals, 2023 AISI 304 SS has good corrosion resistance in a variety of environments but does not have good resistance to wear. Aggressive marine environments require materials that can withstand both the biocorrosion and the wear associated with the impact of waves ...
Hugo Pérez +3 more
semanticscholar +1 more source
Effect of Micro-Shot Peening on the Fatigue Performance of AISI 304 Stainless Steel
Metals, 2021 The effects of micro-shot peening on the rotating bending fatigue resistance of AISI 304 stainless steel (SS) were investigated in this study. The strain-hardening, surface roughness and induced residual stress were inspected and correlated with fatigue ...
Yu-Hsuan Chung +3 more
semanticscholar +1 more source