Results 91 to 100 of about 51,635 (273)
A Review on Microreactor Design for Effective Fischer–Tropsch Process Intensification
Advanced Materials Technologies, Volume 11, Issue 4, 19 February 2026.Design strategies for effective Fischer–Tropsch process intensification are summarized based on experimental and simulation experiences. Recommendations for catalyst loading of packed‐bed and wash‐coated microchannel, microtube, micromonolith, and microstructured reactors are discussed.
Yangjun Wei +5 more
wiley +1 more source
ANALISA LAJU KOROSI PADA PUMP IMPELLER DI INDUSTRI PERTAMBANGAN BATU BARA
Jurnal Teknik Mesin, 2016 Korosi merupakan kerusakan material logam yang disebabkan reaksi antara logam dengan lingkungannya yang menghasilkan oksida logam dan sulfida logam atau hasil reaksi lainnya yang lebih dikenal sebagai pengkaratan.
Puguh Ogi Nur Rachman
doaj +1 more source
Friction stir welding of AISI 304 austenitic stainless steel
Materialwissenschaft und Werkstofftechnik, 2007 AbstractThe objective of this work is to demonstrate the feasibility of friction stir welding (FSW) AISI 304 austenitic stainless steels. The tool used was formed of a tungsten‐based alloy. The specimens were welded on an 11 kW vertical milling machine.
Meran, Cemal. +2 more
openaire +5 more sources
Engineering Reports, Volume 8, Issue 2, February 2026.A low‐cost clip gauge extensometer for crack mouth opening displacement was developed from accessible procedures and materials. Accuracy and repeatability comparable to commercial devices were demonstrated in calibration and fracture tests, enabling reliable measurement in CT specimens for resource‐constrained laboratories.
Isaías Chamorro‐Cruz +8 more
wiley +1 more source
Characterization of Laser Structuring on AISI 304 Stainless Steel
Al-Nahrain Journal for Engineering SciencesSuper-hydrophobic is the tendency of a surface to spit out water droplets. Only a surface with high apparent contact angle (>1500), low contact angle hysteresis (<100), low sliding angle (<50), and strong Cassie model state stability is considered a super-hydrophobic surface.
Sarah Sabah Edan, Rana M. Taha
openaire +2 more sources
Metals, 2019 The melt-pool behaviors during selective laser melting (SLM) of Al2O3-reinforced and a eutectic mixture of Al2O3-ZrO2-reinforced AISI 304 stainless-steel composites were numerically analyzed and experimentally validated. The thermal analysis results show
Abolhasani +5 more
semanticscholar +1 more source
Plasma Processes and Polymers, Volume 23, Issue 2, February 2026.Plasma‐activated aerosol (PAA) can produce RONS‐rich droplets useful for microbial inactivation. PAA treatment induces near‐complete inactivation of both bacterial and fungal loads, highlighting peroxynitrite‐driven antimicrobial activity and strong potential for scalable sanitization.
Pasquale Isabelli +4 more
wiley +1 more source
Defence Technology, 2019 This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels. The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting ...
Wichan Chuaiphan +1 more
doaj +1 more source
A Study on the Failure of AISI 304 Stainless Steel Tubes in a Gas Heater Unit
Metals, 2019 This paper investigates a failure in convection section tubes of a gas heater unit in a petrochemical plant. Tubes are made of AISI 304 stainless steel. The failure is reported after 5 years of service at working temperature 500 °C. The failure is in the
A. Bahrami, P. Taheri
semanticscholar +1 more source
steel research international, Volume 97, Issue 2, Page 955-966, February 2026.This study investigates how drawing process parameters affect the tribological behavior of AISI 304 steel sheet. Under lubricated conditions, increasing normal force, drawing speed, and countersamples roughness reduces the coefficient of friction by up to 21%.
Felipe de Souza Leal +6 more
wiley +1 more source