Results 41 to 50 of about 155,733 (169)
Applied Research, Volume 5, Issue 5, October 2026.Laser surface treatment was carried out to enhance the performance of Ni‐Al2O3 coatings on HSS substrates. The results revealed improved microstructural features, corrosion resistance and significant reduction in slurry erosion wear with 18 W laser treatment. ABSTRACT The sliding wear between hydraulic vane tip and the inner surface of the cam ring can
Majunath Keshav +3 more
wiley +1 more source
Zinc Element Traces to Inhibit Scale Formation on Cooling Tower and Air Cooler Systems
Iraqi Journal of Chemical and Petroleum Engineering, 2013 Calcium carbonate is predominantly present in aqueous systems, which is commonly used in industrial processes. It has inverse solubility characteristics resulting in the deposition of scale on heat transfer surface.
Shaymaa Abdul Rahman Ahmed Reshan
doaj
Nature of Surface Microcracks on Phosphorus Micro‐Alloyed Copper
Materials and Corrosion, Volume 77, Issue 10, Page 1644-1652, October 2026.SSRT tests and microscopic characterization methods were used to study the effect of plastic deformation and environment on the formation of surface microcracks on Cu‐OFP. Results show that, while ambient conditions produced thousands of microcracks per mm2, exposure to sulfide water resulted in fewer microcracks with no evidence of crack growth ...
Ahsan Chonche +4 more
wiley +1 more source
Ultrasonic Vibration Assisted Laser Processing: A Hybrid Paradigm for Extreme Surface Enhancement
Rare Metals, Volume 45, Issue 10, October 2026.ABSTRACT Traditional laser processing techniques offer many advantages, but they often encounter limitations such as heat‐affected zones, recast layers, residual tensile stresses, and poor surface finish. The integration of ultrasonic vibration (UV) presents a promising hybrid approach to overcome these challenges by introducing beneficial effects like
Aziz Ul Hassan Mohsan +6 more
wiley +1 more source
Journal of Infection in Developing Countries, 2013 Introduction: Contaminated sponges might lead to cross-contamination in kitchens since they can transfer microorganisms to surfaces where microorganisms can survive for hours or days and contaminate food. The main objective of this study was to evaluate
Eliandra Mirlei Rossi +2 more
doaj +1 more source
Materials and Corrosion, Volume 77, Issue 9, Page 1579-1594, September 2026.Schematic depicting corrosion layer formation and changes in stainless steel exposed to Solar Salt at 600°C for 1000 h under different atmospheres: (a) N2 accelerates salt decomposition, producing nitrite and oxide ions, causing severe corrosion. (b) Adding O2 reduces nitrite ions formation, resulting in less corrosion than N2 alone.
Sumit Kumar +4 more
wiley +1 more source
Fatigue Strength Determination of AISI 316L Steel and Welded Specimens Using Energy Methods
Engineering ProceedingsAISI 316 is a stainless steel known for its exceptional corrosion resistance and excellent mechanical properties. It is used in the chemical and pharmaceutical industries, food processing equipment, and medical devices.
Danilo D’Andrea +3 more
doaj +1 more source
Materials and Corrosion, Volume 77, Issue 9, Page 1424-1437, September 2026.This article examines the impact of externally introduced chromium compounds on the localized corrosion of 316 L stainless steel in acidic chloride environments such as hydrochloric acid. While the corrosion resistance of 316 L relies on the formation of a chromium‐rich passive oxide layer, industrial conditions may expose the steel to various chromium
Florence Lequien
wiley +1 more source
Integrity of 316/420 Stainless Steel Tribosystem Under Severe Marine Conditions
MetalsThe present study aims to examine the tribological and mechanical integrity of AISI 316/420 stainless steel tribosystem under boundary lubrication with artificial seawater for application in a marine environment.
Karla J. Moreno +3 more
doaj +1 more source
Revista Facultad de Ingeniería Universidad de Antioquia, 2013 We have investigated the oxidation of austenitic stainless steels AISI SAE: 304, 316 and 317, at temperatures of 700 to 750°C in an atmosphere approaching 100% of steam, and in a time range of 10 to 1000h of exposure. The purpose is to check the quality
José Luddey Marulanda +2 more
doaj +1 more source