Results 21 to 30 of about 3,242 (217)

Effects of composition on the in-reactor creep of AISI 316 [PDF]

Journal of Materials for Energy Systems, 1980
Compositional variations affect the inreactor creep of 316 stainless steel. Pre- and postirradiation diametral change measurements of pressurized tube specimens irradiated at 450 °C to 4.6 × 1022 n/cm2 E > 0.1MeV) have indicated that increases in the solute concentrations of silicon, phosphorus, and molybdenum retard irradiation creep. The data suggest
Bates, J.F., Gilbert, E.R.
openaire   +1 more source

Influence of strain temperature in formability of AISI 316 stainless steel [PDF]

, 2023
openLa formatura della lamiera effettuata a temperature sottozero sta riscuotendo sempre più interesse in ambito industriale in quanto può rappresentare un'alternativa alla formatura a temperatura ambiente in termini di deformabilità e alla formatura ...
PIERASCO, MARCO
core  

Дослідження корозійної стійкості зварних металорукавів зі сталей AISI 304 та AISI 316 [PDF]

, 2015
Despite a large number of available data regarding the causes of damage of steel structures made of stainless steel of AISI 304 and AISI 316 grades, little attention has been paid to the manufacturing and storage conditions of these steel grades, but ...
Носовський, Борис Іванович, Іванов, Віталій Петрович, Моргай, Федiр Вiкторович, Солідор, Наталя Аркадіївна   +3 more
core   +4 more sources

Diffusion Bonding and Transient Liquid Phase (TLP) Bonding of Type 304 and 316 Austenitic Stainless Steel—A Review of Similar and Dissimilar Material Joints

Metals, 2020
Similar and dissimilar material joints of AISI grade 304 (1.4301) and AISI grade 316 (1.4401) austenitic stainless steel by solid state diffusion bonding and transient liquid phase (TLP) bonding are of interest to academia and industry alike. Appropriate
Abdulaziz AlHazaa, Nils Haneklaus
doaj   +1 more source

A Preliminary Study on the Quality of Joining AISI 316 and AISI 3415 Steel by the near Solidus Forming Process

Metals, 2023
In this study, the Near Solidus Forming (NSF) process, which falls under the umbrella of semi-solid processes, was utilized to coforge an AISI 316 tube and an AISI 3415 rod into an as-forged valve geometry. The billet used for the process was kept as large as possible to increase the contact surface area between the two materials.
Gorka Plata, Olaia Gordo-Burgoa, Jokin Lozares, Andrea Sánchez, Asier Bakedano, Iñaki Hurtado, Carl Slater   +6 more
openaire   +3 more sources

Mechanical, Microstructure and Corrosion Properties of Friction Stir Welded Dissimilar Austenitic Stainless Steel Joints [PDF]

Materials Research
In many industries, challenges arise when welding dissimilar materials using traditional methods, such as fusion welding. These challenges often lead to problems like cracking, phase segregation, and intermetallic formation.
Sundar raju Govindaraj, Senthil Vaithilingam, Sivakumar Karuppan   +2 more
doaj   +1 more source

Improving Cavitation Wear Resistance of Cast Iron Valve Castings by Applying Austenitic Steel Overlays [PDF]

Archives of Foundry Engineering
This study presents the results of cavitation wear resistance tests of AISI 307 and AISI 316 steel overlays. The overlays were applied using plasma cladding.
M. Jacek-Burek, M. Mróz
doaj   +1 more source

Breakdown and evolution of the protective oxide scales of AISI 304 and AISI 316 stainless steels under high-temperature oxidation [PDF]

, 2011
The failure of the protective oxide scales of AISI 304 and AISI 316 stainless steels has been studied and compared at 1,000°C in synthetic air. First, the isothermal thermogravimetric curves of both stainless steels were plotted to determine the time ...
Saura Barreda, Juan J., Bellés Bellés, Joan, K. A. Habib, Cervera González, Iván, M. S. Damra, I. Cervera, J. J. Saura, Habib Ameen, Kudama, J. Bellés, Damra, M. S.   +9 more
core   +1 more source

Characterization of the expanded austenite developed on AISI 316 LM steel by plasma nitriding [PDF]

Journal of Mining and Metallurgy. Section B: Metallurgy, 2017
AISI 316 LM samples were plasma nitrided at a temperature of 380°C for different times between 0.5 and 8 h in a 85%N2- 15%H2 gas mixture. Different experimental techniques such as: optical microscopy (OM), X- ray diffraction (XRD ) and glow ...
Keddam M., Thiriet T., Marcos G., Czerwiec T.   +3 more
doaj   +1 more source

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316 [PDF]

Engineering and Technology Journal, 2020
RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal
Safa Lafta, Maan Tawfiq
doaj   +1 more source