Results 71 to 80 of about 2,308 (222)
Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process
Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima +4 more
wiley +1 more source
Comparison of test methods for crevice corrosion propagation and repassivation potential of stainless steel AISI 316 [PDF]
The crevice corrosion propagation modes and repassivation potential of stainless steel AISI 316 in chloride solution were compared using cyclic potentiodynamic polarization (CPP), potentiodynamic-galvanostatic-potentiodynamic (PD-GS-PD) and Tsujikawa ...
Ali, Syed Talat +2 more
core +1 more source
The Investigation of Ultrasonic Energy Attenuation in AISI 316 Stainless Steel Weld Joint [PDF]
, 2017 This research aims to study and describe the effect of microstructure on shape of distance amplitude correction (DAC) curve and ultrasonic inspectability of stainless steel weld joint.
Mai Noipitak, Boonhlua Khwansri
core +1 more source
Review of Electrochemical Methods for Battery Recycling
Chemie Ingenieur Technik, Volume 98, Issue 5, Page 191-211, May 2026.Electrochemical methods for the recycling of batteries are reviewed and different approaches for enhanced leaching, separation, and recovery methods are compared regarding their efficiency and suitability for potential application. ABSTRACT Research on innovative methods for the recycling of battery waste materials using electrochemical procedures is ...
Christian Modrzynski
wiley +1 more source
Caracterização superficial do aço inoxidável 316 L eletropolido via técnica eletroquímica de reativação potenciodinâmica [PDF]
, 2005 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico.
Paranzini, Alexandre Stefano
core
Revista Facultad de Ingeniería Universidad de Antioquia, 2013 We have investigated the oxidation of austenitic stainless steels AISI SAE: 304, 316 and 317, at temperatures of 700 to 750°C in an atmosphere approaching 100% of steam, and in a time range of 10 to 1000h of exposure. The purpose is to check the quality
José Luddey Marulanda +2 more
doaj +1 more source
Optimization of Cutting Parameters in CNC Turning of AISI 304 and AISI 316 Stainless Steel [PDF]
International Journal of Trend in Scientific Research and Development, 2018 This paper deals with finding optimal cutting parameters to get the better surface finish. It uses Taguchi method of experiments in arriving at optimal cutting speed, feed rate and depth of cut on turning operation. Turning is common method for cutting, especially for the finished machined products.
Nethaji Perumal A +2 more
openaire +1 more source
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, Volume 28, Issue 8, 22 April 2026.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
BEHAVIOR OF ALUMINUM COATING BY CVD-FBR IN STEAM OXIDATION AT 700°C
CT&F Ciencia, Tecnología & Futuro, 2014 Aluminum coatings have been obtained using the Chemical Vapor Deposition of Fluidized Bed Reactor technique (CVD-FBR), on austenitic stainless steels (AISI 304, AISI 316 and AISI 317), in order to evaluate resistance to steam oxidation at 700ºC.
José-Luddey Marulanda-Arévalo +2 more
doaj
Engineering Reports, Volume 8, Issue 4, April 2026.Welding power and post‐weld heat treatment (PWHT) at 850°C influence phase transformations in S32205 duplex stainless steel, promoting sigma phase formation and reducing corrosion resistance. PWHT at 850°C also replicates HAZ‐like microstructures in base metal, enabling improved characterization of weld joint properties.
Sandra Chacón‐Fernández +2 more
wiley +1 more source