Results 91 to 100 of about 67,372 (213)
Corrosion of Steels in Liquid Bismuth–Lithium Alloy
MetalsThe corrosion resistance of several types of steel (AISI 410, 321, 316L, 904L) was determined in a liquid Bi-Li (5 mol.%) alloy (BLA) medium at 650 °C combining gravimetric analysis of steel samples and chemical analysis of corrosion products’ content ...
Aleksander V. Abramov +4 more
doaj +1 more source
Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Microstructure and Corrosion Properties of Orthodontic Brackets by Laser Treatment
International Journal of Electrochemical Science, 2017 The austenitic stainless steel AISI 316L has been chosen as the material for orthodontic bracket. This paper reported our studies on the surface of the stainless steel 316L treated by laser heat input.
Xiaoyan Zhang, Yu Song, Xinhong Wang
doaj +1 more source
Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process
Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima +4 more
wiley +1 more source
, 2021 Due to their high corrosion resistance, non-transformation, and non-magnetism, austenitic stainless steels can meet the service requirements. However, their low hardness and poor wear resistance impose serious drawbacks. A combination of plasma nitriding
Z. Wang +8 more
semanticscholar +1 more source
دراسة بعض العوامل المؤثرة على لحام المونة لربط الفولاذ مقاوم الصدأ (CK مع الفولاذ منخفض الكاربون ( 15 ( AISI 316L ) [PDF]
Engineering and Technology Journal, 2008 Similar Plates of stainless steel (AISI 316L) and dissimilar plates ofstainless steel (AISI 316L) and low carbon steel (Ck15) are welded by brazingusing copper base non- active filler metal alloys in furnaces with inert gasatmospheres The specimens were ...
doaj +1 more source
Dust Cake Pressure Drop Determination of Surface Filters at Low Absolute Pressures
Chemical Engineering &Technology, Volume 49, Issue 5, May 2026.This study examines how the pressure drop of dust cakes on surface filters changes when the absolute pressure is reduced. In addition, it evaluates whether a model previously used to describe clean filter media can also capture the pressure drop behavior of dust cakes, thereby clarifying its applicability and limits under low absolute pressure ...
Vanessa Löschner +2 more
wiley +1 more source
Sinterização por micro-ondas de um aço AISI 316L reforçado com carbeto de boro [PDF]
, 2018 It aims to analyze the microwave sintering of an AISI 316L steel reinforced with boron carbide...Sem bolsaTem por objetivo analisar a sinterização por micro-ondas de um aço AISI 316L reforçado com carbeto de boro..
Neves, Ederson Bitencourt das
core +3 more sources
Review of Electrochemical Methods for Battery Recycling
Chemie Ingenieur Technik, Volume 98, Issue 5, Page 191-211, May 2026.Electrochemical methods for the recycling of batteries are reviewed and different approaches for enhanced leaching, separation, and recovery methods are compared regarding their efficiency and suitability for potential application. ABSTRACT Research on innovative methods for the recycling of battery waste materials using electrochemical procedures is ...
Christian Modrzynski
wiley +1 more source
Nano- and Micromechanical Parameters of AISI 316L Steel [PDF]
, 2020 Access full text - https://doi.org/10.3103/S1068375520060071The nano- and micro-indentation mechanical parameters of the AISI 316L stainless steel, such as nanohardness (НNI), microhardness (HMI), the Young modulus (E), the indices of plasticity (H/E ...
GRABCO, D. +8 more
core +1 more source